Safety Instructions For; Further Risks - Femi D 305 Manual Del Usuario

EN
3. Do not use saw blades which are damaged or
deformed.
4. Only use saw blades recommended by the manufacturer
and which conform to EN 847-1 standard; take care that
the selection of the saw blade accounts for the material
to be cut; before replacing the blade ascertain that outer
diameter and bore diameter are consistent with those
used on the mitre saw, that the riving knife is thinner
than the groove cut made by the saw blade and not
wider than blade's body, and the speed marked on the
blade exceeds the speed of the machine indicated on
the data plate.
5. Do not use any saw blade manufactured from high speed
steel, marked with " HS "; use blades with carbide inserts
marked with " HW ".
6. Ensure that the arm is securely fi xed when bevelling.
7. Connect the saw to a dust collection device when sawing
wood.
8. Wear suitable personal protective equipment when
necessary, this could include: hearing protection to
reduce the risk of induced hearing loss; respiratory
protection to reduce the risk of inhalation of harmful
dust; gloves for handling saw blades (saw blade shall
be carried in a holder wherever practicable) and rough
material.
9. Always put the pusher away when you do not use it.
10. As soon as you discover any faults in the machine,
including malfunctions of protection devices or saw
blade, report them.
11. Do not use the saw to cut other materials than the ones
recommended by the manufacturer.
12. The user must know all lifting and transportation
information and do not to use guards for this purpose.
13. Keep the fl oor area around the machine free of loose
materials, e.g. chips and cut-off s.
14. It is recommended to use the mitre saw in a properly
lightened area.
15. The operator must know all blade replacement
procedures including prescriptions and warnings for
correct guarding repositioning both in mitre saw and
bench saw mode.
16. Use pusher or push-block handle to avoid working with
the hands close to the saw blade when using in the
table-saw mode.
17. The operator must be adequately trained in the use,
adjustment and operation of the machine.
18. When using the machine as a table saw, ensure that the
arm is securely fi xed in its working position.
19. Stop the saw when unattended.
20. Ensure that the bench is securely fi xed at the suitable
height.
21. When using the machine as a circular saw, ensure
that the upper portion of the saw blade is completely
covered.
22. Ensure that the machine is always fi xed to a bench
whenever possible.
23. Refrain from removing any cut-off s or other parts of the
workpiece from the cutting area whilst the machine is
running and the saw head is not in the rest position.
24. The long pieces of wood, which protrude from the
workbench of the machine, must be adequately
supported by trestles or similar means, to prevent them
from falling off .
25. The riving knife must be always correctly placed: the
distance between it and the toothed rim of the saw blade
shall be between 3 mm and 8 mm and not be lower than
5 mm from the tooth peak.
16
26. During transportation the upper part of the saw blade
shall be covered.
27. In table sawing mode the lower additional protection
must always be mounted.
28. When the saw blade is jammed in the workpiece,
always switch off the machine before removing the
workpiece.

SAFETY INSTRUCTIONS FOR

FURTHER RISKS

- Do not force the machine unnecessarily: excessive
cutting pressure may lead to rapid deterioration of the
blade and a decrease in performance in terms of fi nish
and cutting precision.
- When cutting aluminium and plastics always use the
appropriate clamps: all workpieces must be clamped
down fi rmly.
- Avoid accidental starts: do not press the start button
while inserting the plug into the socket.
- Always use the tools recommended in this manual to
obtain the best results from your cutting-off machine.
- Always keep hands away from the work area when the
machine is running; before performing tasks of any kind
release the main switch button located on the handgrip,
thus disconnecting the machine.
- Ensure the locking pin no.16 (Fig.2) is inserted
completely when the machine is used as a circular
saw.
Working with an electric machine can be dangerous if you
do not follow suitable safety measures. As for any electric
machine with moving parts, the use of a tool entails some
risks. If you use the machine as prescribed in this manual,
you pay careful attention to the work you are doing, you
observe the regulations and you use the suitable personal
devices of protection, you can reduce the probability of risk.
The possible further risks are related to:
1 direct or in direct contacts with electrical shock
2 injuries due to contact with moving or rotating parts, and
especially mitre saw's teeth
3 injuries due to contact with angular or cutting parts when
replacing the blade
4 injuries due to the ejection of tool parts or of the material
you are processing
5 injuries due to noise while cutting
6 injuries due to inhalation of dangerous dust
7 injuries due to the fact that the tool has been not correctly
assembled