Introduction To Use - Femi 2201 SPECIAL Manual De Instrucciones

INDEX
1 INTRODUCTION TO USE ..........................................8
2 INSTALLATION ..........................................................9
3 ADJUSTING .............................................................10
4 USE ..........................................................................11
5 ACCESSORIES .......................................................13
6 MAINTENANCE .......................................................13
7 TROUBLESHOOTING .............................................14
1

INTRODUCTION TO USE

Before starting work with your sawing machine, carefully
read this instructions manual so that you are familiar with the
machine and its uses and where it should not be used. Keep
this manual in a safe place. It is an integral part of the machine
and should be used for reference in operating the machine
correctly and in the proper safety conditions.
Use the machine only and exclusively for the uses specifi ed
below, as recommended in this manual. The machine should
not in any way be tampered with, or forced, or used for
unsuitable purposes.
1.1 CONVENTIONAL SYMBOLS
Never underestimate the warnings "ATTENTION - CAUTION"
given in this manual. In order to draw the user's attention and to
preserve safety, hazardous operation are preceded by symbols
and notes that point out the danger and explain how to behave
to avoid any risk. These symbols and notes are divided in three
categories, identifi ed by the following words:
WARNING: dangerous-behaviours that could cause
serious injuries.
CAUTION: behaviours that could cause slight injuries
or damages to things.
NOTE: the notes preceded by this symbols are technical
and are aimed at making operations easier.
1.2 SAFETY AND RULES
The machine was designed and built according to the
Community Directives in force EC/2006/42 - EC/2004/108
- EC/2006/95.
Moreover, all technical standards relating to this type of product
have been complied with which provide warranty of compliance
with above mentioned directives.
The enclosed CE declaration of conformity together with the CE
brand on the product essentially comprise and are an integral
part of the machine : both guarantee product conformity with
the aforsaid safety Directives.
8
All manuals and user guides at all-guides.com
1.3
The safety plates/labels and indicators present on the machine,
the location of which is shown in the Figure on the inside cover,
are as follows:
1.4
This machine has been designed and developed for cutting
metals.
It can cut:
•
•
•
•
•
•
•
It is not suitable for cutting:
•
•
Consult the relative sections for cutting capacities, the speeds
to use and the type of tools for use according to the material
to be cut and its section. (See list of contents).
1.5
• Do not use the machine in very damp places or in the
presence of infl ammable liquids or gases.
• Do not use it in the open air when general weather and
environmental conditions are unfavourable (eg. explosive
atmospheres, during a storm or rain).
• Do not force the machine unnecessarily : excessive cutting
pressure could cause rapid wear to the blade and negatively
infl uence the performance of the machine in terms of fi nishes
and cutting precision.
• Avoid starting of the machine by accident : do not keep the
button in the handgrip pressed when you plug into the mains
and check that the main switch is in position 0 (zero).
• Wear suitable clothes, without wide sleeves or articles such
as scarves, chains and bracelets which could get caught in
the moving parts.
• Always use personal protection devices: protective goggles
as recommended by safety standards, gloves of the right
size, headphones or earplugs, and hairnets if necessary.
• Use the tools recommended in this manual if you want to
achieve the best performance from your sawing machine.
• Do not use the power supply cable to disconnect the plug form
the outlet. Protect it from sharp edges and do not expose it
to high temperatures.
• Any power cable extensions must be type approved abd
comply with safety standards.
• Avoid using the machine if your psycho-physical condition
are precarious or upset or under the effects of alcohol or
sedatives.
SAFETY PLATES/LABELS
- Wear noise protection devices.
- Wear safety masks or goggles.
- Do not insert the hands in this area with the
tool operating. Danger of dragging/cutting.
RECOMMENDED AND NOT RECOMMENDED
USAGE
COMMON STEELS (FE 37...)
SPECIAL STEELS (C 40, 18NiCrMo5...)
ALUMINIUM AND ITS ALLOYS
BRASS
BRONZE
STEEL TUBING (FE 35, FE 52...)
PROFILED SECTIONS IN SHEET METAL AND
ALUMINIUM
WOOD AND SIMILAR MATERIALS
BONE AND SIMILAR MATERIALS
STANDARD SAFETY PROCEDURS