Tabla de contenido
Idiomas disponibles
Idiomas disponibles
NOTICE Detergent cannot be applied with the high pressure
nozzles (Cyan, Orange or Red).
6.
Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE You must attach all hoses before you start the
2.
engine.
* Startingthe enginewithoutall the hosesconnected and without
3.
thewaterturnedONwill damage the pump.
, Damage to equipment r esultingfrom failureto follow this
4.
instructionwill voidwarranty.
5.
.
8.
Start engine following instructions How to Start Your
Pressure Washer.
Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
9.
Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as neededto prevent
surface from drying. DO NOTallow detergent to dry on
(prevents streaking).
NOTICE You must flush the detergent siphoning system
after each use by placing the filter into a bucket of clean
water, then run the pressure washer in low pressure for 1-2
minutes.
Pressure Washer Rinsing
For Rinsing:
1.
Remove soap PrecisionSpray
TM
nozzle from nozzle
extension.
2.
Select and install desired high pressure nozzlefollowing
instructions How to Use PrecisionSpray MNozzleSystem.
3.
Keep spray gun a safe distance from areayou plan to
spray.
_i, WARNING Kickback from spray gun can cause you to
fall.
• Operate pressure washerfrom a stablesurface.
= Beextremely carefulif you mustusethe pressure washerfrom
a ladder,scaffolding,or anyothersimilarlocation.
= Firmlygraspspraygun with bothhandswhen usinghigh
pressuresprayto avoidinjurywhenspraygun kicks back.
4.
Apply a high pressure spray to a small area and then
check surface for damage, if no damage is found, you
can assume it is okay to continue rinsing.
5.
Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Cleanin9 Detergent Siphonin9 Tube
If you used the clear detergent siphoning tube, you must
flush it with clean water before stopping the engine,
1.
Placedetergent siphoning tube/filter in a bucket full of
clean water.
Remove high pressure nozzlefrom nozzle extension.
Select and install a soap nozzlefollowing instructions
How to Use PrecisionSprayTM NozzleSystem.
Flush for 1-2 minutes.
Shut off engine following instructions How to Stop
Pressure Washerand turn off water supply.
6.
ALWAYS point spray gun in a safe direction push red
button and squeezespray gun trigger to release retained
high water pressure.
NOTICE Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.
_i, WARNING The high pressure stream of water that
this equipment produces can cut through skin
and its underlying tissues, leading to serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.
• Keephigh pressure hoseconnected to pumpand spraygun
whilesystemis pressurized.
• ALWAYS pointspraygun in safedirection,pressredbutton
andsqueeze sprayguntriggerto release highpressure, e very
time youstop engine.
AutomaticCool DownSystem(Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engages to cool the pump by discharging
the warm water onto the ground.
15
Tabla de contenido
