Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Select magenta jetsoap PrecisionSpray
TM
nozzle to
launch soap to second story siding and windows.
JET SOAP
Select black fan soap PrecisionSpray
TM
nozzle for
general cleaning. Greatfor applying soap to
vehicles, boats, driveways, decks, and patios.
FAN SOAP
3.
Pull back on collar, insert new PrecisionSpray
TM
nozzle
and releasecollar. Tug on nozzleto makesure it is securely
in place.
Usage Tips
*
For most effective cleaning, keep PrecisionSpray
TM
nozzle
from 8 to 24 inches (20 to 61 cm) away from cleaning
surface.
*
If you get PrecisionSpray
TM
nozzletoo close, especially
using a high pressure nozzle,you may damage surface
being cleaned.
*
DONOT get closer than 6 inches (15 cm) when cleaning
tires.
2-m-I SoapSystem
_i, WARNING Chemical Burn Hazard.
i_
Chemicals could cause bodily injury, property
damage or death.
• DONOT usecausticliquid with pressure washer.
• UseONLYpressure washersafedetergents/soaps. Followall
manufacturers i nstructions.
Cleaning and ApplyingDetergent with the
Project Pro® PerfectMix
TM
Siphon
To apply undiluted detergent using the blue
PerfectMWMsiphon, follow these steps:
1.
Review use of PrecisionSpray
TM
nozzles.
2.
Attach PerfectMWMsiphon hose to pump
and PerfectMWMconcentrate bottle.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the siphon into a detergent solution bottle, route
the tube so as to keep it from inadvertently contacting the hot
muffler.
3.
Make sure fan soap (black) or jet soap nozzle (magenta)
is installed.
NOTICE Detergentcannot be applied with the high pressure
nozzles(Cyan, Orange or Red).
4.
Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE You must attach all hoses before you start the
engine.
• Starting the engine without all the hoses connected and without
the water turned ON will damage the pump.
• Damageto equipment resulting from failure to follow this
instruction will void warranty.
5.
Start engine following instructions How to Start Your
Pressure Washer.
6.
Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
7.
Allow detergent to "soakin" for 3-5 minutes before
washing and rinsing. Reapply as neededto prevent
surface from drying. DO NOT allow detergent to dry on
(prevents streaking).
Cleaningand ApplyingDetergent with __
the Standard Clear Siphon
To apply diluted detergent using the
standard clear siphon tube, follow these
steps:
1.
Review use of PrecisionSpray
TM
nozzles.
2.
Attach clear siphon hose to barbed fitting on pump.
3.
Mix detergent solution as required by job.
4.
Placesmall filter end of clear siphoning tube into
container with diluted solution as described above.
NOTICE DO NOT insert standard siphon hose in Extreme
Concentrate.Failure to dilute concentrate will cause excessive
application and consumption of solution.
NOTICE Make sure the filter is fully submerged in fluid
while applying solution.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the siphon into a detergent solution bottle, route
the tube so as to keep it from inadvertently contacting the hot
muffler.
5.
Make sure fan soap (black) or jet soap nozzle (magenta)
is installed.
14
Tabla de contenido
