Tabla de contenido
Idiomas disponibles
Idiomas disponibles
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the siphon into a detergent solution bottle, route
the tube so as to keepit from inadvertently contacting the hot
muffler.
3.
Make sure black detergent spray tip is installed.
NOTE:Detergent cannot be applied with the high pressure
spray tips (White, Yellow or Red).
4.
Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE
You must attach all hoses before you start the
engine.
• Starting the engine without all the hoses connected and without
the water turned ON will damage the pump.
• Damageto equipment resulting from failure to follow this
instruction will void warranty.
5.
Start engine following instructions How to Start Your
Pressure Washer.
6.
Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
7.
Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as neededto prevent
surface from drying. DO NOTallow detergent to dry on
(prevents streaking).
Cleaning and ApplyingDetergent with
the StandardClear Siphon
To apply diluted detergent using the
standard clear siphon tube, follow these
steps:
1.
Review use of spray tips.
2.
Attach clear siphon hose to barbed fitting on pump.
3.
Mix detergent solution as required by job.
4.
Place small filter end of clear siphoning tube into
container with diluted solution as described above.
NOTE:DO NOT insert standard siphon hose in Extreme
Concentrate. Failureto dilute concentrate will cause excessive
application and consumption of solution.
NOTE:Make sure the filter is fully submerged in fluid while
applying solution.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the siphon into a detergent solution bottle, route
the tube so as to keepit from inadvertently contacting the hot
muffler.
6.
Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE You must attach all hoses before you start the
engine.
• Starting the engine without all the hoses connected and without
the water turned ON will damage the pump.
• Damageto equipment resulting from failure to follow this
instruction will void warranty.
.
8.
Start engine following instructions How to Start Your
Pressure Washer.
Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
9.
Allow detergent to "soakin" for 3-5 minutes before
washing and rinsing. Reapply as neededto prevent
surface from drying. DO NOT allow detergent to dry on
(prevents streaking).
IMPORTANT:You must flush the detergent siphoning system
after each use by placing the filter into a bucket of clean
water, then run the pressure washer in low pressure for 1-2
minutes.
Pressure Washer Rinsing
For Rinsing:
1.
Remove black detergent spray tip from spray tip
extension.
2.
Select and install desired high pressure spray tip
following instructions How to Use Spray Tips.
3.
Keep spray gun a safe distance from area you plan to
sp ray.
A. WARNING
Kickback from spray gun can cause you to
fall.
• Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure washer from
a ladder, scaffolding, or any other similar location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
4.
Apply a high pressure spray to a small area and then
check surface for damage. If no damage is found, you
can assume it is okay to continue rinsing.
5.
Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
5.
Make sure black detergent spray tip is installed.
NOTE:Detergent cannot be applied with the high pressure
spray tips (White, Yellow or Red).
14
Tabla de contenido
