Ordinary Maintenance - Volpi Olytech 455SP Manual De Empleo Y Mantenimiento

The 4 leds U on the battery, indicate the battery charge status:
Three green leds -->
Two green leds -->
One green led -->
One red led -->
Charge the battery indoor, in a fresh, dry and aired environment.
Do not disassemble, drill, warm, wet, or modify the battery and the charger.
If the machine is not used for a long time, charge the battery completely, disconnect it from the machine
and store it. Recharge the battery every 6 months. If the battery is not charged for more than 6 months,
it can be damaged, and the warranty condition expire.
7. TINES REPLACEMENT
Codes 455SP-L-XL-555SP-L-XL-655SP-L-XL-665SP-L-XL-Ref. fig. E (fig. E.1, E.2, E.3, E.4)
Identify the type of tine to be replaced using the drawing E.1.
Replace tines 2D/2S. 3D/3S and 4D/4S following the procedure described in fig. E.3:
With the socket wrench R (provided) and the 2,5mm wrench K (provided), unscrew the tine's locking nut
D until the tine is free to come out from its housing P and support Y. If the tine does not come out easily,
use the tool S (included) and a hammer to push it slowly out from its housing in the direction indicated
by the arrow.
Fix the new tine in the support Y and then in the housing P, pushing it down eventually using a hammer.
Tighten the screw and the locking nut up to the limit.
Replace tines 1D/1S following the procedure in fig. E.2 and fig. E.4: move manually the tines in the
position of maximum closure, as indicated by the 2 arrows in fig. E.2 and rotate the head on itself.
In this position, from the bottom hole F, use the 3mm wrench K (provided) to unscrew the tine's locking
screw until the tine is free to come out from its housing P and support Y. If the tine does not come out
easily, use the tool S (included) and a hammer to push it slowly out from its housing in the direction
indicated by the arrow.
Fix the new tine in the support Y and then in the housing P, pushing it down eventually using a hammer.
Tighten the locking screw up to the limit.
8.

ORDINARY MAINTENANCE

Codes 455SP-L-XL-555SP-L-XL-655SP-L-XL-665SP-L-XL Rif. Fig. F
MAINTENCANCE
Maintenance has to be carried on by qualified personnel, following the instructions of this manual and
using only original spare parts. User has to follow all the applicable safety laws, using as necessary the
right protective equipment.
IMPORTANT: Every 50 working hours, the internal mechanisms of the head have to be
lubricated with grease for high temperatures. The points have to be lubricated according to
the picture F.
Follow the instructions in fig. F for the grease input.
Rotate the head in order to have access to the rear part (fig. F.1) and identify the two holes V. Unscrew
the two screws W, as indicated in fig. F.2. Using one needleless syringe, as indicated in fig. F.3, put the
grease inside using the holes V. Reassemble the screws and tighten them down.
LONG TERM MAINTENANCE
In case of long lasting inactivity periods, the machine has to be carefully cleaned and then protected
from dust and humidity in a dry place clear from direct sun and freeze. The battery shall not be
connected with the machine as is it is not in use. It shall be stored with full charge and re-charged every
6 months.
COMPANY WITH QUALITY SYSTEM
MANAGEMENT CERTIFIED BY ICIM
80÷100% battery charge
50÷80% battery charge
30÷50% battery charge
-30% battery charge
Tel. +39 0376 76009 Fax +39 0376 76408 www.volpioriginale.it
= ISO 9001 =
Davide e Luigi Volpi S.p.A.
Via San Rocco, 10 – 46040 Casalromano (MN) – Italia
42