For Best Results - Cooper Lighting MS80 Manual De Instrucciones

- I ncrease the separation between the equipment and receiver.
- C onnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- C onsult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user's authorization to operate this equipment.

FOR BEST RESULTS

• Install the motion sensor/transmitter 8-12 feet above the ground. (Motion sensor is less
sensitive above 12 feet.)
• Locate motion sensor so motion moves across
detection zone (Fig. 1).
• Locate sensor away from heat producing sources to
prevent false triggering. Also be very careful not to
include objects such as windows, white walls and
water in the detection zone.
• Locate sensor away from moving objects such as
trees, large shrubs and street traffic.
• Install a wall switch adjacent to the power source.
This helps you operate AUTO and MANUAL OVERRIDE with ease. See OPERATING YOUR
FIXTURE for further information.
• Do not install more than one motion activated fl oodlight on one wall switch.
• For outdoor installation, a location under eaves is preferable.
INSTALLING THE BULB
1. Turn off the power at the main fuse/breaker box.
2. Remove retaining screw (D) that holds glass
lens cover in place. Carefully remove glass lens
cover (Fig. 2).
3. Push old bulb into spring-loaded socket and pull
opposite end out of the other socket.
4. Using a clean cloth or gloves, remove new bulb
from package and protective wrap.
NOTE: Never touch bulb with bare hands as oil from
your skin can cause premature failure.
5. To install bulb, position bulb into spring-loaded
socket and push bulb toward socket until it
depresses. Position other end of bulb into stationary
socket (opposite socket). Be sure each end of bulb
is securely seated against the socket.
6. Replace glass lens cover. Insert and tighten the
retaining screw that secures the glass lens cover.
NOTE: Be sure lens gasket is installed correctly on
housing (A) before reattaching glass lens cover.
NOTE: Make sure your lamp housing is not positioned
within two inches of house.
CAUTION: When replacing bulb in fixture,
always replace with the same wattage bulb or a
lower wattage bulb. DO NOT replace with a bulb
of greater wattage than specified on the fixture.
To do so could create a fire hazard and/or shorten
the life of the bulb. Make sure to disconnect
power and allow fixture to cool before removing
burned-out bulbs.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE: Fixture can be wall or eave mounted only. NOT
suitable for ground mount installation.
NOTE: Do not position lamp housing within two inches
of house.
NOTE: Coverplate mounts to recessed mounted
standard junction boxes (Fig. 3). Junction box must be
at least 1-1/2 inch in depth for proper installation for
recessed mount application.
NOTE: Before installing fixture, be sure to install bulb.
See INSTALLING THE BULB for proper bulb installation.
1. Thread fixture wires through coverplate gasket (E)
(Fig. 4). Position the gasket (E) to match up screw
holes on the floodlight coverplate with the junction
box screw holes.
Fig. 1
Fig. 2
Fig. 3
1-1/2 inch 1-1/2 inch
Round Octagonal
Fig. 4
A
E
C
2
2. Connect the black wire from the fixture to the black
house supply wire and the white wire from the
fixture to the white supply wire using the wire
connectors (G) provided. Attach the ground wire
coming from your house to the ground wire from
the fixture using wire connector (G) provided.
If no house ground wire is available, attach the
ground wire from the fixture to the junction box
if it is metal and grounded. If junction box is not
metal and no house ground wire is available, an
alternative ground source must be used for safe
operation (Fig. 5).
3. Attach fixture (A) to the junction box with two of the
screws (F) provided. Either (2) #6 or (2) #8 screws
will work with most standard junction boxes.
4. Apply silicone caulk around the edges of the
coverplate to provide a watertight seal from rain
and moisture.
5. Turn on power at main fuse/breaker box.
OPERATING YOUR FIXTURE
1. Rotate both knobs on bottom of the sensor to "T"
(test) (Fig. 6).
2. Turn on power to the fixture. The fixture will turn on
for approximately 40 seconds to warm up and then
turn off.
3. Aim sensor head in desired position. (Make sure
sensor head is positioned with control switches
facing towards the ground.)
4. Walk through the detection area. The fixture turns
on when you move and turns off when you stop.
Wait for the fixture to turn off before moving to test
the fixture again.
5. Adjust motion sensor up (larger coverage area),
down (smaller coverage area), left or right until you
cover your desired detection area.
NOTE: Maintain air spacing between lamps and sensor
head– at least 1/2 inch.
6. The time adjustment knob controls how long the
lighting will stay on after the motion has been
detected. While the light fixture is off, turn the time
adjustment knob to the desired length of time. The
floodlight will remain on after the last motion is
detected (8 seconds to 12 minutes) (Fig. 7).
7. The LUX adjustment knob determines the light level
at which the lighting system will start operating
when you set the sensor to automatic operation.
In this setting the floodlight will remain in the OFF
position during daylight hours. Turn knob closer
to for light to turn on (with motion) at night or
turn closer to "T" for light to start detecting motion
at dusk (Fig. 8).
8. This fixture has a manual override feature which
will keep the floodlight on regardless of motion
detection. To activate this function, turn the wall
switch OFF-ON-OFF-ON within 2 seconds. You
can reset the fixture to automatic detection mode
by turning the fixture off for at least 10 seconds
and then turning it back on.
SELECTING YOUR DESIRED FEATURE
Desired Time Adjust
Operation Knob Setting
"Auto" Setting Auto setting
(motion activated)
between
Lights should turn ON "+" and "T"
with motion only at night
and turn OFF after
8 seconds-12 minutes
of no motion.
Standard Floodlight Auto setting
Setting (Manual Override) between
Lights should stay ON "+" and "T"
continuously both
day and night.
(Must be reset manually.)
Fig. 5
White
fixture wire
Black
fixture wire
G
Fixture ground
House ground
Black house
power wire
White house
power wire
Fig. 6
Fig. 7
Approximately Approximately
8 seconds 12 minutes
Fig. 8
Wall ON/OFF LUX Control
Switch Setting Knob Setting
Keep the power to Auto setting
the fixture ON. between
and "T"
Turn the power Auto setting
OFF-ON-OFF-ON between
within 2 seconds. and "T"