Cooper Lighting MS34 Instrucciones

MS34 (Black)
MS34W (White)
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Hammer
• Outdoor weatherproof silicone caulking
• (2) 150 watt (MAX) PAR 38 floodlight bulbs
NOTE: This fixture was designed to work with up to 150 watt maximum PAR halogen flood
bulbs. For improved energy efficiency, lower wattage PAR halogen flood bulbs may be used.
Compact Fluorescent (CFL) bulbs contain electronics which may interfere with the motion
sensing function of your fixture and are not recommended.
HOW IT WORKS
Your motion activated floodlight senses heat images from
objects such as people, large animals and automobile engines.
When motion is detected, the lights will automatically turn
on. Once motion has stopped, the lights will turn off after a
preselected time delay. Your motion activated floodlight may
also be used as a standard floodlight.
WARNINGS AND CAUTIONS
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• For outdoor use only.
• cULus LISTED for wet locations.
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
• Fixture should be installed by persons with experience in household wiring or by a qualified
electrician. The electrical system, and the method of electrically connecting the fixture to it,
must be in accordance with the National Electrical Code and local building codes.
• Fixture should be mounted to a grounded recessed mounted standard junction box marked
for use in wet locations.
• NOT suitable for ground mount installation.
• Keep away from flammable objects. Do not position fixture within
two inches of any combustible materials.
• Always replace bulb with the same wattage or lower wattage than included. Installing a
bulb of a higher wattage could create a fire hazard. Use of a higher wattage bulb will void
the warranty.
• Do not allow sensor head to touch light housing – maintain at least 1 inch space between
fixture and sensor.
• For proper operation and protection against damage, the motion sensor head adjustment
knobs must be facing the ground.
• MINIMUM 90° C SUPPLY CONDUCTORS.
Questions? / ¿Preguntas ? 1-800-334-6871 [email protected]
PACKAGING CONTENTS / CONTENIDO DEL PAQUETE
A. Motion detector and light fixture
Detector de movimiento y
artefacto de luz
110 degrees
B. Coverplate gasket
Junta de la placa de cubierta
D. (2) #6 and (2) #8 mounting screws
(use the size that fits your junction box)
(2) Tornillos #6 y (2) tornillos #8 de montaje
(utilice el tamaño que mejor se adecue a
su caja de conexión)
• Disassembly of your fixture will void the warranty.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install the motion sensor/transmitter 8-12 feet
above the ground. (Motion sensor is less sensitive
above 12 feet.)
• Locate motion sensor so motion moves across
detection zone (Fig. 1).
• Locate sensor away from heat producing sources to
prevent false triggering. Also be very careful not to
include objects such as windows, white walls and
water in the detection zone.
• Locate sensor away from moving objects such as
trees, large shrubs and street traffic.
Up to
60 feet • Do not install more than one motion activated
floodlight on one wall switch or the same circuit since
this may cause interference between fixtures.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE: Fixture can be wall or eave mounted.
NOTE: Coverplate mounts to recessed mounted
standard junction boxes (Fig. 2). Junction box must be
at least 1-1/2 inch in depth for proper installation for
recessed mount application.
1. Turn off power at main fuse/breaker box.
2. Match up screw holes on the floodlight coverplate
with the junction box screw holes.
3. Thread fixture wires through coverplate
gasket (B) (Fig. 3).
4. Connect fixture black wire to house black wire
and connect fixture white wire to house white wire
using wire nuts (E) provided (Fig. 3). (No ground
wire is required. Attach any ground wire from your
house to junction box.)
5. Attach fixture (A) to the junction box with two
mounting screws (D) provided.
6. Apply silicone caulk around the edges of the
coverplate to provide a watertight seal from rain
and moisture.
7. Insert lampholder gaskets (C) into lampholder
assembly, tightly against lampholder, and screw
bulbs into each lampholder (Fig. 3). (Do not
overtighten bulbs.)
1
Instruction Manual / Instrucciones
C. (2) Lampholder gaskets
(2) Juntas obturadoras
del receptáculo
E. (2) Wire nuts
(2) Tuercas para alambre
Fig. 1
Fig. 2
1-1/2 inch
Round
Fig. 3
E
C
B
A
E
Wall mount
A
Eave mount
1-1/2 inch
Octagonal
D
D
C