Cooper Lighting MS80 Manual De Instrucciones

MS80 (Black)
MS80W (White)
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Flathead screwdriver
• Drill
• Outdoor weatherproof silicone caulking
HOW IT WORKS
Your motion activated floodlight senses heat images
from objects such as people, large animals and
automobile engines. When motion is detected, the
lights will automatically turn on. Once motion has
stopped, the lights will turn off after a preselected
time delay. Your motion activated floodlight may
also be used as a standard floodlight.
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Read and follow these instructions.
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Suitable for wall mount or eave mount only. NOT suitable for ground mount installation.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
• Do not remove adjusting screw. Tighten the connection of the fixture head assembly
and motion sensor to the base to avoid any rotation.
WARNING
• Bulb gets HOT quickly!
• The bulb and fixture get extremely hot during use. Disconnect power and allow fixture
to cool before changing bulb or handling fixture.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Always replace bulb with the same wattage or lower wattage than included. Installing
a bulb of a higher wattage could create a fire hazard. Use of a higher wattage bulb will
void the warranty. (Maximum 150 watt halogen bulb.)
Questions? / ¿Preguntas ? 1-800-334-6871 [email protected]
PACKAGING CONTENTS / CONTENIDO DEL PAQUETE
A. Light fixture and
motion detector
Accesorio y
detector de
movimiento
D. Retaining screw
Tornillo de retención
110 degrees
B. 150 watt quartz halogen bulb
Foco halógeno de cuarzo
de 150 vatios
C. Coverplate
Placa protectora
de la lámpara
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture must be mounted to a grounded recessed junction box marked for use
in wet locations.
• Suitable for wall mount or eave mount only. NOT suitable for ground mount installation.
• Do not allow sensor head to touch light housing – maintain at least 1/2 inch space
between fixture and sensor.
• Keep away from flammable objects. Do not position fixture within
2 inches of any combustible materials.
Up to 70 feet
• Do not position lamp housing within 2 inches of house.
• Never touch the bulb with your bare hands, as oil from your skin
can cause premature failure. Always handle bulb with gloves or
a soft cloth.
• For proper operation and protection against damage, the motion sensor head
adjustment knobs must be facing the ground.
• For maximum bulb life, position fixture so the quartz
halogen bulb remains within 4 degrees of horizontal.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including amplifiers) that produce heat.
• Only use attachments/accessories specified by the manufacturer.
• MINIMUM 90° C SUPPLY CONDUCTORS.
• If lens is replaced, use only tempered safety glass of equal thickness per
UL requirements.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation. Under Part 15 of the FCC Rules, any changes or
modifications to the motion detector described in this instruction sheet that are
not expressly approved by Cooper Lighting, LLC could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
1
Instruction Manual / Instrucciones
E. Coverplate gasket
Junta de la placa
de cubierta
F. (2) #6 and (2) #8 mounting screws
(use the size that fits your junction box)
(2) Tornillos #6 y (2) tornillos #8 de montaje
(utilice el tamaño que mejor se adecue a
su caja de conexión)
G. (3) Wire nuts
(3) Conectores de cable
4˚