Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Instruction on mounting and use
Consult the designs in the front pages referenced in the text
by alphabet letters.
Closely follow the instructions set out in this manual. All
responsibility, for any eventual inconveniences, damages or
fires caused by not complying with the instructions in this
manual, is declined.
Suction Cooker hood Description - Fig. 1- various models
1. Vapour collector
2. Suction grill
3. Controls
4. Light point
Use
The hood is designed to be used either for exhausting or filter
version.
Note: the elements marked with the symbol "(*)" are optional
accessories supplied only with some models or elements to
purchase, not supplied.
Ducting version
The hood is equipped with a top air outlet B1 and with a back
air outlet B2 for discharge of fumes to the outside (exhaust
pipe and pipe fixing clamps not provided). Fig. 2.1
Filtering version
In the case where it is not possible to discharge the cooking
fumes and steam outside, the hood can be used in the
filtering version, mounting 1 or 2 active carbon filters (*).
The fumes and steam are recycled into the kitchen. Fig. 2.2
The models with no suction motor only operate in ducting
mode, and must be connected to an external suction device
(not supplied).
Installation
The minimum distance between the supporting surface for the
cooking vessels on the hob and the lowest part of the range
hood must be not less than 50cm from electric cookers and
65cm from gas or mixed cookers.If the instructions for
installation for the gas hob specify a greater distance, this
must be adhered to.
Electrical connection
The electrical tension must correspond to the tension noted on
the label placed inside the cooker hood. Connect the electrical
plug, where provided, to the an easily accessible outlet in
conformity with local standards in force. Where an electrical
plug is not provided (for direct connection to electrical
network) or is not easily accessible, place a standards
approved bipolar switch that provide full disconnection under
overvoltage category III conditions, in accordance with the
wiring rules.
Attention: substituting the supply cable must be carried out
by the authorised technical assistance service.
Mounting
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take
the weight of the hood. Do not tile, grout or silicone this
appliance to the wall. Surface mounting only.
Before beginning installation:
•
Remove the fats filter/s or the suction grill/s (depending
on the model in possession –see also the relative
paragraph). This/these is/are to be mounted once
installation is completed.
•
Remove the active carbon (*) filter/s if supplied (see also
relative paragraph). This/these is/are to be mounted only
if you want lo use the hood in the filtering version.
•
Check (for transport reasons) that there is no other
supplied material inside the hood (e.g. packets with
screws (*), guarantees (*), etc.), eventually removing
them and keeping them.
•
In addition check whether near the installation area of the
hood (in the area accessible also with the hood mounted)
an electric socket is available and it is possible to
connect a fumes discharge device to the outside (only
suction version).
•
Choose the discharge outlet to use:
Only filtering version: use ONLY the upper B1 outlet
(Fig. 2 - Fig. 2.2). Check that this, once installation is
completed, is not obstructed and that there is sufficient
space so that the purified fumes and steam can return
easily into the kitchen.
Press with decision (Fig. 3.1) to take away the pre-
fractured part (B1 o B2) that closes the discharge outlet
and remove it.
Install the connection ring on the open discharge outlet
(Fig. 3.2 bayonet embedded) or the deflector (*). (Fig.
3.3).
Check that the lateral wall units between which to install the
hood are sufficiently robust for installing the hood.
Otherwise mount the hooking brackets on the wall (*) to use
as additional supports:
a.
Insert each bracket from the rear inside the hood
through the apposite slots (Fig. 4.1—Fig. 4.2).
b. Fix the brackets with the screws and threaded bushes
(Fig. 4.3).
Screw the headless screws halfway. They will serve to
adjust the position of the hood at the moment of
installation.
Note: the position of the brackets can be adjusted during
installation, suitably loosening and retightening the screws
that fix them to the hood. (Fig. 7 - S1-S2).
Installing the aesthetic panel (*)
a.
Extract the steam collector (freeing it from the blocking
hooks - Fig. 5).
9
Tabla de contenido
