Electrical Connections; System Check; First Time Operation Instructions; Getting Started - Warn ZEON Guía De Instalación Y Operación

Idiomas disponibles

Idiomas disponibles

Step 2 - Install the Wiring
To prevent serious injury or death. Always
WARNING
place the supplied terminal boots on wires and terminals as
directed by the installation instructions.
To prevent serious injury or death from
WARNING
electrical fi re:
Never route electrical cables across sharp edges.
Never route electrical cables near parts that get
hot.
Never route electrical cables through or near
moving parts.
Avoid pinch and wear/abrasion points when
installing all electrical cables.
Always insulate and protect all exposed wiring
WARNING
and electrical terminals.
NOTICE A fully charged battery and good connections are
essential to the proper operation of your winch. The minimum
requirement for a 12 volt DC battery is 650 Cold Cranking Amps.
Route battery connection cables in areas which
will not cause them to chafe or cut through the
insulation causing a potential short circuit.
The winch power wire must be routed to the
battery. A direct battery connection of the power
(red) and ground (black) cable is required. Do not
connect ground to vehicle chassis.
Routing the battery connection cables may
require removal of vehicle facia or body parts.
Always route battery cables along a path that
allows the cables to be secured with zip ties.
Loose or unsecured power cables can cause
WARNING
serious injury or death.
Always protect power cables from sharp edges,
areas that get too hot to touch with your hand and
any moving parts.
Wireless Control
Activation Switch
Control Pack Ground
Wire

ELECTRICAL CONNECTIONS

1. Plan the routing path.
2. Loosely secure power cables along path.
3. Confirm power cables are protected from sharp
edges, heat and moving parts. Consider chassis
flex and vibration which might damage cable.
4. Carefully inspect electrical cable routing. Zip tie
and secure electrical cables. Zip ties should be
snug, but not cutting into wire insulation. Use
electrical tape, pieces of rubber hose or electrical
conduit to protect electrical cables and wire
harness where needed to avoid electrical cable
insulation wear or abrasion.
5. FIRST, attach the winch power (red) cable to the
positive (+) battery terminal. SECOND, attach the
ground (black) cable to the negative (-) battery
terminal.
Always connect red (+) power cable ONLY to the
WARNING
positive (+) terminal of the battery.
Always connect black ground (-) power cable ONLY
WARNING
to the negative (-) terminal of the battery.
Step 3 - System Check
Perform system check:
1. Check fasteners and make sure they are tight and
to proper torque
2. Verify the wireless control activation switch light
turns ON. A flashing green light appears in the
switch. If light does not turn on, immediately
check to ensure power cables are correctly
connected to the battery, red to (+) and black to (-).
If not, disconnect and reconnect as instructed.
3. Verify all electrical wiring to all components is
correct and be certain that all connections are
tight.
4. Verify there is no exposed/bare wiring, terminals or
cable insulation damage.
5. Read The Basic Guide to Winching Techniques
completely before operating your winch.
6. Charge remote.
Once you have performed a system check, you are
ready to perform "First Time Operating Instructions".
Ground (black) Cable
Power (red) Cable
WARN INDUSTRIES
13
FIRST TIME OPERATING INSTRUCTIONS
Step 4 - First Time Operating Instructions
Take time to fully read the Instructions and/or
WARNING
Operations Guide and the Basic Guide to Winching Techniques,
in order to understand your winch and its operations.

Getting Started

Your ZEON® Platinum Winch is operated by the
new Advanced Wireless Remote Control.
The Advanced Wireless Remote Control is
designed to allow the operator to control the winch
and two auxiliaries remotely.
1. Verify the wireless control switch (located on
back of control pack) is "ON" (a green flashing
light appears inside switch). The switch must
be 'ON' (activated) in order for the Advanced
Wireless Remote Control to operate the winch.
Charging the Battery
Your WARN® Advanced Wireless Remote Control
is powered by an internal rechargeable lithium ion
battery. Although the battery will arrive partially
charged, you must fully charge the battery or plug
into a power source before use.
1. Connect the included USB charger to the
Advanced Wireless Remote Control.
2. Plug other end of the USB charger into a power
source (such as the included auto charger, a
wall charger or a computer USB port). NOTE:
Remote is operable while charging.
3. The remote control will power on and the
charging icon (
battery indicator in the upper right corner of
the menu, indicating the remote is charging.
4. The remote is fully charged when the battery
indicator icon is filled. NOTE: Allow a minimum
of two hours for battery to fully charge.
The Status Bar
The status bar allows the operator to keep track
of the wireless signal strength and the remote's
battery life during all menu operations. NOTE: A
strong wireless signal and a fully charged battery is
recommended for optimal performance.
Wireless Signal
Strength
92821A3
92821A3
The bars on the wireless signal strength icon will
light up in sequence to show signal strength.
X
No Signal
Weak Signal
The remote control's battery indicator icon
indicates the state of the internal battery by
changing color and fill level of battery icon.
Fully charged battery (green)
Low charged battery (yellow)
Critically low battery (red)
NOTE: If your battery icon shows at a critically low level,
you must charge the battery or plug into power source.
Wireless Control
Home Menu
Activation
Switch
Turn on the remote by pressing any button. This
will automatically bring up the Home Menu.
From the Home Menu, you can access each of
the four operations.
Four Operations:
1) Winching
3) System Settings
Winching
Settings
) will appear inside the
1. Use the left and right buttons on your remote
to navigate through the operation menus.
Left
2. To activate an operation, press select.
Battery Indicator
Icon
NOTE: To return to the Home Menu from other
menus, navigate to the Home Icon (
bar and press Select.
WARN INDUSTRIES
14
Fair Signal
Strong Signal
2) Auxiliary
4) Power Off
Auxiliary
Power Off
Right
Select
) in the menu
loading