Accessories - Metabo BS 175 Manual Original

- Remove adjusting nut (2) with open-ended
spanner.
Caution! Left-hand thread on left machine
side, i.e. to release the adjusting nut (2)on the left
machine side, turn clockwise!
- Remove clamping flange (3) and grinding
wheel (4).
- Secure new grinding wheel (4) in the reverse
order.
- Remount the safety cover (1). Tighten screws.
- Adjust the spark deflector (10) and workpiece
support (8) as described in chapter 8.2 and 8.1.
Replacing the wet grinding wheel
(TNS 175 only):
- Empty the water container (18): hold a collecting
pan under the container and remove the rubber
stopper (19). Re-insert the rubber stopper.
- Loosen the 3 screws (17) adequately and lower
the water container.
- Using one hand, hold the grinding wheel (4)
secure. Caution! Risk of injury! Wear protec-
tive gloves!
- Remove adjusting nut with open-ended spanner.
(Loosen by turning anti-clockwise).
- Remove clamping flange and grinding wheel (4).
- Secure new grinding wheel (4) in the reverse
order.
- Replace the water container (18). (17) Tighten
screws. Fill the water container with the correct
amount of water (see chapter 8.5)
9.2 Replacing the sanding belt (BS 175
only)
Remove the side sanding belt cover (16): release
the 2 screws (13), slide the sanding belt cover (16)
(bayonet catch) and remove.
Swivel out lever (12) as far as it will go. This relieves
sanding belt tension and it can now be removed
from the rollers.
Place the new sanding belt on the rollers so that its
direction of circulation (arrows on the inside of the
sanding belt) matches the arrow (15) (16)on the
side sanding belt cover.
Return the lever (12) to the original position to
tension the sanding belt.
Place the side sanding belt cover (16) on the 2
screws (13) and slide (bayonet catch). Tighten the
two screws.
Adjust the belt run (see chapter 8.6).
For sanding belts, see Accessories chapter 10.
9.3 Water container (TNS 175 only)
Regularly replace the water in the water container
(18). To do this, hold a collecting pan under the
container and remove the rubber stopper (19).
Dismantle the water container for cleaning
purposes, as described in chapter 9.1. Use water
and a brush (no metal bristles) to clean the inside
of the container.
a

10 Accessories

Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
A Grinding wheels ..................... Order No.:
D= 125 mm:
36 P: .................... 0900025181
60 N: .................... 0900025190
D= 150 mm:
36 P: ........................... 6.30632
60 N: ........................... 6.30633
D= 175 mm:
36 P: ........................... 6.30657
60 N: ........................... 6.30656
D= 200 mm:
36 P: ........................... 6.30784
60 N: ........................... 6.30785
D= 250 mm:
36 P: ........................... 6.30636
60 N: ........................... 6.30637
Wet grinding wheel
D= 200 mm: .................... 0900025653
B Stand
Order No.: ................................ 6.23867
C Wall bracket
Order no.: .......................... 6.23862
D Sanding belts
3 x P 40 .............................. 0900025777
3 x P 60 .............................. 0900025688
3 x P 80 .............................. 0900025696
3 x P 100 ............................ 0900025785
3 x P 120 ............................ 0900025700
3 x P 180 ............................ 0900025807
3 x P 240 ............................ 0900025823
3 x P 400 ............................ 0900025840
For a complete range of accessories, see
www.metabo.com or the main catalogue.
ENGLISH
ENG
15