Data Table - Stiebel Eltron DCE 10 Plu Funcionamiento E Instalación

iNSTallaTiON
Specification

16.7 Data table

Electrical data
Rated voltage
1
Rated output
Rated current
2
Recommended circuit breaker size
3
Min. recommended wire size (AWG copper)
Frequency
Phase
Resistivity ρ15 ≥
Conductivity σ15 ≤
Max. mains impedance at 50 Hz
Connections
Water connection
Application limits
Max. permissible pressure
Max. inlet temperature for reheating
Temperature setting range
Values
Max. inlet temperature (e.g. pasteurization)
Activation rate
Hydraulic data
Nominal capacity
Versions
Adjustable connected load
Protection class
Insulating block
Heating system
Cover and back panel
Color
IP rating
Dimensions
Height
Width
Depth
Weights
Weight
1
For units with adjustable power output, factory default setting is jumper position 2 [high]
2
Overcurrent protection sized at 100% of load. Tankless water heaters are considered a non-continuous load. Use only GFCI Class A circuit breakers.
3 Copper conductors with a temperature rating of 75 °C or greater must be used.
load.
These are our recommendations. Check local codes for compliance if necessary.
Note
The water heater conforms to IEC 61000-3-12.
www.stiebeleltronamericas.com
DCE 10 Plus
238150
V 208 220
kW 5.4/7.2 6.0/8.0
A 25.8/34.4 27.3/36.4
A 30/35 30/40
8
Hz 50/60
1/N/GND | 2/GND
Ω cm 1100
μS/cm 910
Ω 0.0407 0.0385
½˝ NPT
MPa 145 (1)
°F (°C) 131 (55)
°F (°C) 68–140 (20–60)
°F (°C) 158 (70)
gpm (l/min) 0.264 (1.0)
gal (l) 0.07 (0.277)
Yes
1
Plastic
™
Direct Coil
Plastic
White
IP 24
in (mm) 14 / ˝ (372)
5
8
in (mm) 8 / ˝ (217)
9
16
in (mm) 4 / ˝ (109)
5
16
lb (kg) 5.5 (2.50)
Conductors should be sized to maintain a voltage drop of less than 3% under
DCE 13 Plus DCE 15 Plus
238151 238152
240 208 220 208
7.2/9.6 11.8 13.2 9.0/10.7
30.0/40.0 56.7 60.0 43.3/51.6
30/40 60 50/60
6 6
50/60 50/60
1/N/GND | 2/GND 1/N/GND | 2/GND
1100 1100
910 910
0.0353 0.0248 0.0234 0.0272
½˝ NPT z˝ NPT
145 (1) 145 (1)
131 (55) 131 (55)
68–140 (20–60) 68–140 (20–60)
158 (70) 158 (70)
0.264 (1.0) 0.264 (1.0)
0.07 (0.277) 0.07 (0.277)
No Yes
1 1
Plastic Plastic
™
Direct Coil Direct Coil
Plastic Plastic
White White
IP 24 IP 24
14 / ˝ (372) 14
5
8
8 / ˝ (217) 8
9 9
16
4 / ˝ (109) 4
5 5
16
5.5 (2.50) 5.5 (2.50)
220 240
10.0/12.0 12.0/14.4
45.5/54.5 50.0/60.0
0.0257 0.0235
™
/ ˝ (372)
5
8
/ ˝ (217)
16
/ ˝ (109)
16
DCE Plus| 19