Tabla de contenido
Manual operation
All programming and full functionality of the timer are available in the B-hyve
app. If you have the need, there are some basic operations you can perform
directly at your timer.
FUNCTION
Hold
until the display shows MANUAL and flashes
Manual Watering -
WATER ALL ZONES. To WATER ALL ZONES for a default of
10 min. each*, wait without pressing a button until WATER
WATER ALL ZONES
ALL ZONES stops flashing and watering will begin.
Hold
until the display shows MANUAL and flashes
WATER ALL ZONES. Quickly press
Manual Watering -
PROGRAM apears. Wait until WATER A PROGRAM stops
WATER A PROGRAM
flashing and press
Once the program letter stops flashing, watering will begin.
Hold
until the display shows MANUAL and flashes
WATER ALL ZONES. Quickly press
WATER A ZONE appears. Wait until WATER A ZONE stops
Manual Watering -
flashing and quickly press
WATER A ZONE
run. When the zone stops flashing the run time will begin
to flash. Quickly press
RUN TIME stops flashing, watering will begin.
Skip Zone
Quickly press
Cancel All
Hold
between 2-5 sec.
Watering
Rain Delay
Set in app;
Digital Lock-Out
Enable/disable in app.
Lights Off Mode
Enable/disable in app.
Hold
for 10 seconds.
On/Off
Quickly press
Hard Reset
*Default watering time for "WATER ALL ZONES" can be customized in the B-hyve App settings.
THE B-HYVE APP
Install the B-hyve® app on your smart device
You will need a smart device to connect the timer to Wi-Fi.
timer connected
symbol
running status/
messaging
rain delay
calendar
program list
remote control or
Note: The app will guide you through initial set up of your sprinkler timer. In
addition, there are help icons throughout the app with more information and
useful tips.
BUTTON PRESS
again and WATER A
to select the desired program to run.
two more times and
to select the desired zone to
to set the desired run time. Once
to skip currently running zone.
blinks yellow and display shows DELAY.
5 times.
weather
& temp.
stop watering
next zone
settings
zone list
home button
FCC & IC Statement
This device complies with Part 15 of the FCC Rules and Industry Canada license exempt RSS standards.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation. FCC Warning: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help This device meets the FCC and IC
requirements for RF exposure in public or controlled environments. The end user is advised to maintain
a distance of 20 cm from the controller and any personnel to ensure compliance with RF exposure
regulations.
This Class B digital apparatus complies with Canadian ICES-003
DÉCLARATION DE FCC ET L'IC
Cet appareil est conforme à la section 15 de la Règlementation de la FCC et la norme RSS d'Industry
Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer
d'interférences nuisibles, et (2) cet appareil doit tolérer toutes les interférences, dont les interférences
pouvant causer un fonctionnement non désiré. Cet appareil numérique de classe B est conforme à la
norme canadienne ICES-003.
Remarque: cet appareil été testé et déclaré conforme aux limites d'exposition pour les appareils
numériques de classe B, selon la section 15 de la Règlementation de la FCC. Ces limites sont conçus pour
fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle.
Cet appareil produit, utilise et peut émettre de l'énergie radio fréquence et, si elle n'est pas installée et
utilisée conformément aux instructions, peut causer des interférences nuisibles aux communications
radio. Cependant, il n'est pas garantie que des interférences ne se produisent pas dans une installation
particulière. Si cet appareil cause des interférences gênantes à la réception d'un signal radio ou de
télévision, ce qui peut être déterminé en allumant et en éteignant l'appareil, l'utilisateur peut corriger les
interférences en suivants une des mesures suivantes :
• Réorientez ou repositionnez l'antenne de réception.
• Augmentez la distance entre l'appareil et le récepteur.
• Branchez l'appareil dans une prise sur un circuit différent du circuit sur lequel le récepteur est branché.
• Consulter le revendeur ou un technicien radio/TV expérimenté pour obtenir de l'aide. Cet appareil est
conforme aux exigences de la FCC et de l'IC concernant
l'exposition aux ondes dans un environnement public ou contrôlé. Il
est conseillé à l'utilisateur final de maintenir une distance de 20 cm du
contrôleur pour assurer la conformité aux réglementations d'exposition
RF. Information de conformité pour le Canada
SPECIFICATIONS
Rated input:
Australia—240V AC 50/60Hz 0.15A
Europe—230VAC 50/60Hz 0.15A
USA—120V AC 60Hz 0.2A
Max load:
AUS & EU—24V AC 1 Amp 50/60 Cycle
USA—24VAC 1 Amp 60Hz
Temperature Operating Range:
Operating: 32–158° F (0–70° C)
Storage & transport:
-4–176° F (-20–80° C)
Humidity Operating Range:
Operating: 0–80% | Storage & transport: 0–90%
Altitude:
6,500' (2,000 meters)
IP65 Rating
Installation Class II
Over Voltage Category II
Need Help?
If the app and the website don't have what you're looking for,
please go to our website before returning this sprinkler timer to
or visit us at:
mybhyve.com
call us
1-801-299-5555
Battery Specifications:
Timer includes a non-replaceable CR2032 Lithium
battery.
This timer works with any standard 24V irrigation
solenoid.
The internal fuse is non-replaceable.
the store.
email us
text us
801-905-8260
Tabla de contenido
