Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
limits to Bevel Angle
Maximum Miter
Max Bevel Angle at Which Cut Can Be
Angle
48° Left Side
48° Right Side
limits to Miter Angle
AT Maximum Bevel
Max Miter Angle at Which Cut Can Be
Angle
48° Left Side
Familiarization (Fig. A, D, L)
Open the box and lift the saw out by using the hand
indentations
8
in the base of the saw (Fig. D).
The miter lock knob
5
is not assembled for shipping.
Remove the miter lock knob from the packaging and screw
onto the saw. Refer to Figure A for position.
You saw has a built-in dust port
supplied, but not assembled, dust bag
system to be connected. Refer to Dust Extraction for
assembly instructions.
Fig. D
Place the saw on a smooth, flat surface such as a workbench
or strong table.
Examine Figure A to become familiar with the saw and its
various parts. The section on adjustments will refer to these
terms and you must know what and where the parts are.
CAUTION: Pinch hazard. To reduce the risk of injury,
keep thumb underneath the operating handle when
pulling the handle down. The lower guard will move
up as the operating handle is pulled down, which
could cause pinching. The operating handle is placed
close to the guard for special cuts.
Press down lightly on the operating handle
out the lock down pin
19
. Gently release the downward
pressure and hold the operating handle, allowing it to rise
to its full height. Use the lock down pin when carrying
the saw from one place to another. Always use the hand
10
Completed
Left Bevel: 40°
Left Bevel: 42.5°
Completed
Left Miter: 31.6°
Right Miter: 35°
that allows either the
12
or shop vacuum
42
2
and pull
indentations
8
to transport the saw as seen in Figure A and
Figure D.
Bench Mounting (Fig. A)
Holes
3
are provided in all 4 feet to facilitate bench
mounting, as shown in Figure A. Always mount your
saw firmly to a stable surface to prevent movement. To
enhance the tool's portability, it can be mounted to a piece
of 1/2" (12.7 mm) or thicker plywood which can then be
clamped to your work support or moved to other job sites
and reclamped.
nOTE: If you elect to mount your saw to a piece of plywood,
make sure that the mounting screws don't protrude from
the bottom of the wood. The plywood must sit flush on the
work support. When clamping the saw to any work surface,
clamp only on the clamping bosses where the mounting
screw holes are located. Clamping at any other point will
interfere with the proper operation of the saw.
CAUTION: To prevent binding and inaccuracy, be
sure the mounting surface is not warped or otherwise
uneven. If the saw rocks on the surface, place a thin
piece of material under one saw foot until the saw sits
firmly on the mounting surface.
COMPONENTS (FIG. A)
WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Intended Use
This heavy duty miter saw is designed for professional wood
cutting applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Changing or Installing a New Saw Blade
(Fig. E–G)
Refer to Saw Blades under Optional Accessories for correct
saw blade.
WARNING: To reduce the risk of serious personal
injury, turn tool off and remove the battery pack
before transporting, making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
CAUTION:
•
Never depress the spindle lock button
the blade is under power or coasting.
•
Do not cut metal, masonry or fiber cement
product with this miter saw.
Removing the Blade (Fig. A, E–G)
1. Remove battery pack
13
2. Raise the arm to the upper position and raise the lower
guard
4
as far as possible.
3. Loosen, but do not remove the guard bracket rear
screw
21
by four revolutions. The bracket
25
while
from the saw.
23
can be
Tabla de contenido
