Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Connecting your equipment
Connecting the speakers
The receiver will work with just two stereo speakers (the front speakers in the diagram) but
using at least three speakers is recommended, and a complete setup is best for surround
sound.
Make sure you connect the speaker on the right to the right (R) terminal and the speaker on
the left to the left (L) terminal. Also make sure the positive and negative (+/–) terminals on the
receiver match those on the speakers.
You can use the speakers connected to the B speaker terminals to listen to stereo playback in
another room. See Switching the speaker system on page 12 for the listening options with this
setup.
You can use speakers with a normal impedance between 6 Ω and 16 Ω.
However, note that only the front speakers are set to a value between 12 Ω and 16 Ω if you
select SPAB in Switching the speaker system on page 12.
Be sure to complete all connections before connecting this unit to the AC power source.
Bare wire connections
1
Twist exposed wire strands together.
2
Loosen terminal and insert exposed wire.
3
Tighten terminal.
CAUTION
• These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric
shock when connecting or disconnecting the speaker cables, disconnect the power cord
before touching any uninsulated parts.
• Make sure that all the bare speaker wire is twisted together and inserted fully into the
speaker terminal. If any of the bare speaker wire touches the back panel it may cause the
power to cut off as a safety measure.
Connect the surround back or front height speakers
Connect the PRE OUT SURR BACK/FRONT HEIGHT outputs of the unit and additional
amplifier to add a surround back or front height speaker.
• The Pre Out setting must be set if the above connections are performed. Select
SURR.BACK if the surround back speaker is connected and HEIGHT if the front height
speaker is connected (If neither the surround back speaker nor the front height speaker is
connected, either setting will suffice) (see The Pre Out Setting on page 37).
• You can use the additional amplifier on the surround back channel pre-outs for a single
speaker as well. In this case plug the amplifier into the left (L (Single)) terminal only.
1
2
3
10 mm
3
(
/
in.)
8
Front right
Subwoofer
LINE LEVEL
INPUT
COAXIAL
OUT
HDMI
DVR/BDR IN
DVD IN
BD IN
VIDEO 1 IN
IN
1
ASSIGNABLE
(
CD
)
VIDEO
AUDIO
SURR BACK/
DVR/BDR
CD-R/TAPE
FRONT HEIGHT
ADAPTER PORT
L
MONITOR
TV/SAT
BD
(Single)
(
OUTPUT 5 V
OUT
IN
IN
OUT
PRE OUT
0.1 A MAX
)
ANTENNA
R
FM
UNBAL
DVR/
CD
75
BDR
L
AM LOOP
SIRIUS
A
OUT
IN
DVD IN
IN
IN
IN
1
R
(
DVD
)
ASSIGNABLE
IN
IN
2
L
DVR/
(
BDR
)
IN
IN
R
SUBWOOFER
MONITOR
OUT
Y
P
P
TV/SAT
BD
DVD
B
R
COMPONENT VIDEO
PRE OUT
Surround right
Surround back or
front height speakers
Right
ANALOG
R
L
R
AUDIO IN
SPEAKER
SPEAKER
Surround back or front height
channel amplifier
Front left
Center
OPTICAL
IN
IN
1
2
ASSIGNABLE
(
TV/SAT
)
(
CD-R/TAPE
)
FRONT
CENTER
SURROUND
B
R
L
R
L
R
L
SPEAKERS
Class 2 Wiring
Surround left
Left
Left
Right
L
Speaker B
02
02
11
En
Capítulos
Tabla de contenido
Solución de problemas
