Worx Leafjet Manual Original página 13

Charging the battery pack
NOTE:
• The batteries are shipped uncharged.
Each battery must be fully charged
before the first use.
• Always fully charge the two batteries at
same time. More details can be found in
charger's manual.
WARNING! The charger and battery
pack are specially designed to work
together, so do not attempt to use any other
devices. Never insert or allow metallic objects
into your charger or battery pack connections
because of an electrical failure and hazard
will occur.
Checking the battery condition
NOTE: Fig. A2 only applies for the battery
pack with battery indicator light.
Installing & removing the battery pack
NOTE:
• This machine will only run when
2 batteries are installed. It is
recommended to use the same
two batteries and charge the two
batteries at the same time.
• When you use two batteries with
different power,the machine will only
run to the level of the lowest charged
battery.
Battery indicator light
See details in BATTERY STATUS part
IMPORTANT:
When only one light is illuminated,
your battery is overly discharged,
even though the machine may still be
capable to work. Continuing to operate
your machine with the battery in this
discharged condition may reduce the life
and performance of your battery.
When no light is illuminated, at least one
battery is not fully installed or battery
may be defective, please double check the
batteries are fully seated into position.
ASSEMBLY
Air speed mode
NOTE: The blower is in the air speed mode for
default assembly.
NOTE: The blower has two working modes: air
speed mode and air volume mode. To change
modes, depress the nozzle release button
and slide backward for air speed mode. Slide
forward for air volume mode.
Choose a suitable mode according to your
work:
- AIR SPEED MODE offers a high-speed,
concentrated airflow for sweeping
smaller areas, clearing debris out of
grass, or dislodging heavy or wet leaves.
- AIR VOLUME MODE offers a high-volume
of mass airflow to cover a larger area or
on hard surfaces.
40V Cordless Blower
Air volume mode
OPERATION
Starting & Stopping
WARNING! The tool runs for a few
See Fig. A1
seconds after it has been switched off.
Let the motor come to a complete standstill
before setting the tool down.
Adjusting the blowing speed / air volume with
2-speed switch
USER TIPS
- Hold the blower tube approximately 8"
above the ground when operating the
See Fig.
tool. Use a sweeping motion from side
A2
to side.
- After blowing the debris/leaves into a pile,
it is easy to dispose of the pile.
Caution!
- Do not blow hard objects such as
nails, bolts, or rocks.
- Do not operate the blower near
See Fig.
bystanders or pets.
B, C
- Use extra care when cleaning debris
from stairs or other tight areas.
- Wear safety goggles or other suitable
eye protection, long pants, and shoes.
Turbo button for power boosting
NOTE:
• Turbo button for power boosting can
increase air flow significantly, and it
can be used for clearing heavy or wet
debris.
• First switch on the blower and select
See Fig. D a speed control (speed I or II), then
depress the turbo button and hold it.
Release the Turbo button, the blower
will return to the previously selected
speed.
BATTERY STATUS (See Fig. D)
• Before starting or after use, press the button beside
the power indicator light on the machine to check the
battery capacity.
• During operation, the battery capacity will be indicated
automatically by the battery power indicator. The
indicator constantly senses and displays the battery
condition as follows.
• For the machine with 2 battery packs with different
power, the power indicator light displays the battery
condition with the lower one of the two batteries.
See Fig. E
Battery
indicator light
status
Five green lights
(
illuminated.
Battery condition
The two batteries are in a highly
) are
charged condition.
See Fig.
F, G
See Fig. H
See Fig.
I1, I2
13
See Fig. J
EN