Tabla de contenido
Idiomas disponibles
Idiomas disponibles
f Never use a chisel accessory in rotary mode. The
accessory will bind in the material and rotate the drill.
f Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it
unstable and may lead to loss of control.
f Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
f Avoid touching the tip of a drill bit just after drilling, as
it may be hot.
f The intended use is described in this instruction
manual. The use of any accessory or attachment
or performance of any operation with this tool other
than those recommended in this instruction manual
may present a risk of personal injury and/or damage
to property.
SAFETY OF OTHERS
f This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
f Children should be supervised to ensure that they do
not play with the appliance.
RESIDUAL RISKS.
Additional residual risks may arise when using the
tool which may not be included in the enclosed safety
warnings. These risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
f Injuries caused by touching any rotating/moving parts.
f Injuries caused when changing any parts, blades or
accessories.
f Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
f Impairment of hearing.
f Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
USING AN EXTENSION CABLE
If an extension cable is requred, use an approved extension
cable suitable for the power input of this tool (see technical
data). The minimum conductor size is 1.5 mm
When using a cable reel, always unwind the cable
completely. Also refer to the table below.
Conductor size (mm
0.75
1.00
1.50
2.50
4.00
Voltage
115
230
FEATURES (Fig. A)
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch
4. Mode selector
5. Tool holder
6. Side handle
7. Depth stop
ASSEMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle
f Turn the grip counterclockwise until you can slide the
side handle (6) onto the front of the tool.
f Rotate the side handle into the desired position.
f Tighten the side handle by turning the grip clockwise.
Warning! Alaways use the tool with the side handle
properly assembled.
Fitting an accessory (Fig.B)
f Clean and grease the shank (8) of the accessory.
f Pull back the sleeve (9) and insert the shank into the
tool holder (5).
f Push the accessory down and turn it slightly until it fits
into the slots.
.
f Pull on the accessory to check if it is properly locked.
2
The hammering function requires the accessory to be
able to move axially several centimetres when locked
in the tool holder.
ENGLISH • 15
)
Cable rating (Amperes)
2
6
10
15
20
25
Cable length (m)
7.5 15
Amperes
Cable rating (Amperes)
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10
10
7.1 - 12.0
15
15
12.1 - 20.0
20
20
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10
10
7.1 - 12.0
15
15
12.1 - 20.0
20
20
25
30
45
60
6
6
6
10
6
6
15 15
10
15
20 20
15
20
20 25
20
25
25
-
25
-
-
-
6
6
6
6
6
6
6
6
6
6
10 15
10
10
15 15
15
15
20 20
20
20
25
-
Tabla de contenido
