Enlaces rápidos
HP Designjet Z5400
PostScript® ePrinter
Product Assembly
EN
Instructions
Instructions d'assemblage
FR
du produit
Instrucciones de montaje
ES
del producto
Instruções de montagem
PT
do produto
© 2013 Hewlett-Packard Company
Large Format Division
Camí de Can Graells 1-21 · 08174
Sant Cugat del Vallès
Barcelona · Spain
All rights reserved
Printed in XXX
Hardware Setup:
EN
1- open the printer box
2- Stand assembly
3- Unpack more components
4- Power and network configuration
5- Printhead and cartridge setup
Software setup:
Now, it's easy to print large-format documents
from virtually anywhere, using your laptop, printer
touchscreen, iPhone®, or iPad®.
Installation du matériel :
FR
1- Ouverture du carton de l'imprimante
2- Assemblage du support
3- Déballage des autres composants
4- Configuration réseau et alimentation
5- Installation des têtes d'impression et des cartouches
Installation du logiciel :
Il est désormais facile d'imprimer des documents grand
format depuis quasiment n'importe où à l'aide d'un
ordinateur portable, de l'écran tactile de l'imprimante,
d'un iPhone® ou d'un iPad®.
Instalación del hardware:
ES
1- Apertura de la caja de la impresora
2- Montaje del soporte
3- Desembalaje de más componentes
4- Configuración de red y alimentación
5- Instalación del cabezal de impresión y el cartucho
Instalación del software:
Ahora resulta muy fácil imprimir documentos de gran
formato desde prácticamente cualquier lugar mediante
un portátil, la pantalla táctil de la impresora, un
iPhone® o un iPad®.
Configuração de hardware:
PT
1- Abra a caixa da impressora
2 - Levante a montagem
3 - Retire mais componentes da embalagem
4 - Configuração de rede e energia
5 - Configuração de cartucho de tinta e cabeçotes de
impressão
Configuração de software:
Agora, é fácil imprimir documentos em grandes
formatos de praticamente qualquer lugar usando
olaptop, a tela sensível ao toque da impressora, o
iPhone® ou o iPad®.
Manuales relacionados para HP Designjet Z5400 PostScript ePrinter
Resumen de contenidos para HP Designjet Z5400 PostScript ePrinter
- Página 1 HP Designjet Z5400 PostScript® ePrinter Hardware Setup: Instalación del hardware: 1- open the printer box 1- Apertura de la caja de la impresora 2- Stand assembly 2- Montaje del soporte 3- Unpack more components 3- Desembalaje de más componentes 4- Power and network configuration 4- Configuración de red y alimentación...
- Página 2 Product working area Read these instructions carefully...What you will need for this procedure Before you start unpacking, consider where you are going to put the • Because the product is heavy, you may need three people to unpack it. When more than one assembled product.
- Página 3 Open the box HP Designjet Z5400 Ouverture du carton PostScript® ePrinter Start Up Apertura de la caja Abra a caixa © 2013 Hewlett-Packard Development Company, L.P. Remove the accessories from the printer box. You will find the documentation and software for Remove the stand box, which is the largest one.
- Página 4 Lift up the sides and top of the printer box, and Dismantle the bottom of the printer box by dis- Cut and remove the straps around the stand box. Remove the pieces of cardboard. remove them from the printer. engaging each corner and then folding down the Do not remove the white protective material sides so that they are out of the way.
- Página 5 Stand assembly Assemblage du support Montaje del soporte Levante a montagem Open the stand box. Remove the cross-brace and the two pieces of Place the two pieces of packaging material on the packaging material from each end of the stand floor, spaced 40 cm apart, and place the cross- box.
- Página 6 4+4=8 A screwdriver and 22 screws are provided in the Attach each leg of the stand to the cross-brace, Make sure you have used 4 screws in each leg. Attach a foot to each leg, using four screws in stand box: 16 screws to assemble the stand, 4 to using two screws on the outside of the leg and each foot.
- Página 7 180° Return to the main body of the product, carefully Remove the small flaps from each of the foam Remove the orange tape from the transparent Open the transparent covering and remove the turn the product upside down in order to attach end pieces.
- Página 8 Place the stand on the product slowly and When the legs are correctly located on the Lift the stand, keeping it upside down. There is a round yellow button protruding from carefully, so that the colored buttons on the legs product, attach them to the product using two the top of one stand leg, and a square green fit into the corresponding holes in the product.
-
Página 9: Important
90° 101.2kg Check that the wheels on the stand are locked. Rotate the product 90 degrees. IMPORTANT: make Hold the product by the foam end pieces and by Remove the foam end pieces. At this point you will have two spare screws. sure that the roll feeds are facing downwards. - Página 10 Remove the transparent covering from the Unlock the brake lever on each of the four wheels Lay out the components of the basket. Fit the basket supports to the stand legs, one to each leg. product. by lifting the lever. Déposez par terre les composants du bac Retirez le couvercle transparent du produit.
- Página 11 Fit the two short tubes to the product’s feet, one Attach the basket’s front tube to the two short Rest the basket’s rear tube on the supports that The basket is now complete. on the front of each foot. Each tube should click tubes on each foot.
- Página 12 Unpack more components Déballage des autres composants Desembalaje de más componentes Retire mais componentes da embalagem Remove all the orange tape pieces from the Open the Window. You will see a cardboard support attached to the product, except for the ones coming from inside product with tape.
- Página 13 Carefully lift the cardboard support up and out of Inside the right-hand side of the product, you Turn the cardboard support 90° to the right. Remove the cardboard carefully. the product. It will not be needed again; you can will see a piece of cardboard. discard it.
- Página 14 Power and network configuration Configuration réseau et alimentation Configuración de red y alimentación Configuração de rede e energia If you find a USB flash drive in a plastic bag inside Connect the power cable to the product’s Connect the network cable or a certified USB 2.0 the box, it contains the latest Firmware.
- Página 15 Configuração de cartucho de tinta e cabeçotes de impressão On the front panel, the HP logo appears. Please Switch on power to the product using the switch The product checks for the presence of ink car- just above the power socket.
- Página 16 Press the ink cover firmly into place until you hear Check that the ink cover is properly placed. Open the cover on the left-hand side of the Insert the ink cartridges one by one. Each car- that it clicks. product. tridge is marked with its own color, and should be inserted only into the slot of the same color.
- Página 17 When you have inserted all of the ink cartridges Open the window and grasp the blue handle of the Pull the blue handle towards you as far as it The cartridges must be inserted the right way correctly, the product must prepare the ink sys- will go.
- Página 18 Press the OK key on the front panel when you Lift the handle up to open the printhead cover. The setup printheads exist only to prevent the Remove and discard all orange setup printheads. The front panel prompts you for the next step: escape of ink during ink cartridge installation.
- Página 19 Insert the printheads one by one. Each printhead Unwrap each printhead and remove all orange Push each printhead into the slot until it clicks Pull the blue handle towards you as far as it will parts. is marked with its own colors, and should be into place.
- Página 20 HP Designjet Z5400 PostScript® ePrinter Start Up © 2013 Hewlett-Packard Development Company, L.P. Push the handle down on top of the printhead While the product is preparing the printheads, you could spend the time installing the product software on Once the printhead check has finished the prod- cover.
- Página 21 When the front panel prompts you to load paper Push the removable stop towards the roll as far From the front of the product, place the spindle If the blue removable stop is on the spindle, for printhead alignment: Take the spindle which remove it.
- Página 22 Go to the rear of the product, and remove the Remove the spindle by lifting out first the right- Feed the leading edge of the paper into the If the blue removable stop is on the spindle, product until the product takes hold of it. Do not orange stoppers from each end of the spindle.
- Página 23 Push the removable stop towards the roll as far Feed the leading edge of the paper into the prod- The product will proceed to align the printheads. From the back of the product, place the spindle as it will go. This process involves printing, and therefore into the product.
- Página 24 HP ePrint: 1 - HP ePrint is a HP web service that allows you to print by simply attaching a PDF, or other print-ready file, to an email and send it to your printer’s dedicated address. To start printing by email you need the printer’s email address and printer code.
- Página 25 1 - HP ePrint est un service Web de HP qui vous permet d’imprimer en joignant simplement un PDF ou un autre fichier prêt à imprimer à un courrier électronique et en l’envoyant à l’adresse dédiée à votre imprimante. Pour...
- Página 26 (necesitará el código de la impresora y una cuenta en HP À l’aide du DVD livré avec votre imprimante, installez le logiciel du produit sur votre ordinateur. Suivez ePrint Center).
- Página 27 1. Return to home screen You can now, or at some later time, color-calibrate the paper type that you intend to use in the product. Color calibration is recommended for accurate color printing. It can be started from the Product 2.
- Página 28 Insert the HP Start Up Kit DVD into your computer. Insérez le DVD du Kit de démarrage HP dans votre Insira o DVD do Kit de inicialização HP no com- Inserte el DVD del Kit de iniciación de HP en el For Windows: ordinateur.