Tabla de contenido
Idiomas disponibles
Idiomas disponibles
3. PAUSE TIME (Aut. closing time programming 4 min. max.):
The control unit is supplied by the manufacturer without automatic closing. To enable automatic closing, proceed as follows: use the SEL
key to position on the flashing LED L3 and press the SET key for an instant; the minimum pause time can be set at approximately 1". The
procedure for programming of this function is as follows:
a) Between 2" and 4" the automatic closing is set to 1"
b) The elapsed time is counted for a time exceeding 4". Once again momentarily press the SET button. At the same time it will cause
saving of the time of automatic closure and LED L3 will come on in a fixed manner. To restore the initial condition (no automatic closing)
select flashing LED L3 and then press the SET key twice consecutively in an interval of 2 seconds. The LED will turn off and the
operation will be completed.
4. FORCE OPEN (Selecting the Speed profile in the Normal Opening cycle):
The control unit allows you to define different motor Speed profiles during the Normal operating cycle in the Opening movement. In the
factory set configuration, motor Speed during opening is set at the maximum level "MAX" (i.e. identical to the setting selected using the
SPEED trimmer with LED L4 off); if you wish to change the profile to a medium level value "MED", proceed as follows: use the SEL key to
select flashing LED L4 and press the SET key; at the same time LED L4 becomes steady on and programming will be completed. If you
wish to change the profile to a Minimum value "MIN" repeat the operation described above, pressing the SEL key twice (LED L4 will flash
rapidly) rather than once. Repeat the operation if you want to restore the initial configuration.
5. FORCE CLOSE (Selecting the Speed profile in the Normal Closing cycle):
The control unit allows you to define different motor Speed profiles during the Normal operating cycle in the Closing movement. In the
factory set configuration, motor Speed during closing is set at the maximum level "MAX" (i.e. identical to the setting selected using the
SPEED trimmer with LED L5 off); if you wish to change the profile to a medium level value "MED" proceed as follows: use the SEL key to
select flashing LED L5 and press the SET key; at the same time LED L5 becomes steady on and programming will be completed. If you
wish to change the profile to a Minimum value "MIN" repeat the operation described above, pressing the SEL key twice (LED L5 will flash
rapidly) rather than once. Repeat the operation to restore the initial configuration.
6. SLOWING OPEN (Selecting the Speed profile in the Opening Slowdown cycle):
The control unit allows you to define different motor Speed profiles during the Slowdown operating cycle in the Opening movement. In the
factory set configuration, motor Speed during the opening slowdown stage is set at the maximum level "MAX" (i.e. identical to the setting
selected using the SLOWING menu with LED L6 off); if you wish to change the profile to a medium level value "MED" proceed as follows:
use the SEL key to select flashing LED L6 and press the SET key; at the same time LED L6 becomes steady on and programming will be
completed. If you wish to change the profile to a Minimum value "MIN" repeat the operation described above, pressing the SEL key twice
(LED L6 will flash rapidly) rather than once. Repeat the operation if you want to restore the initial configuration.
7. SLOWING CLOSE (Selecting the Speed profile in the Closing Slowdown cycle):
The control unit allows you to define different motor Speed profiles during the Slowdown operating cycle in the Closing movement. In the
factory set configuration, motor Speed during the closing slowdown stage is set at the maximum level "MAX" (i.e. identical to the setting
selected using the SLOWING menu with LED L7 off); if you wish to change the profile to a medium level value "MED" proceed as follows:
use the SEL key to select flashing LED L7 and press the SET key; at the same time LED L7 becomes steady on and programming will be
completed. If you wish to change the profile to a Minimum value "MIN" repeat the operation described above, pressing the SEL key twice
(LED L7 will flash rapidly) rather than once. Repeat the operation if you want to restore the initial configuration.
EXTENDED MENU 1
The control unit is factory set to allow direct selection exclusively of the main menu functions.
If you wish to enable the functions described in Extended Menu 1, proceed as follows: select flashing LED LEV and press SET 1 times. The LED will start
flashing alternately 1 0 1 0 1 0. This means you have 30 seconds to select the functions of Extended Menu 1 using the SEL and SET keys; once an
additional 30 seconds have elapsed, the control unit reverts to the main menu.
L1
PROG. REMOTE
L2
DIR. OPENING
L3
PROG. AUTOMATIC
L4
FOTO TEST
L5
DS1 IN OPEN
L6
DO NOT USE
L7
DO NOT USE
LEV
MENU
32
COMUNELLO ®Copyright 2020 - All rights reserved
LED OFF
LED ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
DO NOT USE
DO NOT USE
DO NOT USE
DO NOT USE
1 FLASHING LIGHT
Capítulos
Tabla de contenido
