Jacuzzi sasha Manual De Instalación página 25

( 35, detail 3) Position the roof so that it is within the in-
ner edge of the respective frame, paying attention to the plastic
edge protectors previously attached with silicone.
( 36, detail 1) Connect the shower heads to the mixing
system using the bend fittings supplied (refer to the indicated
labels, which also feature on the tubes themselves).
( 36, detail 2) Connect the light cable to the respective
junction box.
If the shower has a door, install the fixed glass supports
to the roof and the base frame structure; refer to the
attached documentation.
Installing the shower wall (2)
( 37, detail 1) Draw in the wall and connect the pipe com-
ing from the mixing system to the shower cascade.
( 37, detail 2) Place the wall on top of the one underneath,
ensuring coupling, and attach it to the panel as indicated.
Benches and duckboards
Sauna:
( 38, details 1-2) Position the heater cover and proceed
with the positioning of the duckboards (wood) adjacent to the
side walls.
( 38, details 3-4-5) Position the highest bench against the
side wall and connect the light cable underneath the cable coming
from the wall, sealing the cable outlet with the foam rubber bush-
ing.
(details 6-7) Finish positioning the duckboards and then po-
sition the lower bench.
Shower:
( 39) Check that the drain covers are present and then pro-
ceed with the positioning of the duckboard.
Hammam:
( 40 , details 1-2-3) Check that the drain pipe covers are
present; then position the tank under the spout and proceed
with the positioning of the duckboard adjacent to the side wall.
( 40, details 4-5-6) Position the bench against the side wall
and connect the light cable underneath the cable coming from
the wall, sealing the cable outlet with the foam rubber bushing.
(detail 7) Position the second duckboard.
Installing panels
( 41) Connect the cables to the display, attaching them to
the wall.
( 42, details 1-2-3) Thread the light cables in the corner
hole, connecting them to the electrical box cables indicated.
Thread the foam rubber cylinder to the cables and insert it into
the wall hole.
( 42, detail 4) After having checked all connections, close
the equipment zone, by replacing its cover.
( 42, detail 5) Draw the back support towards the side wall
and install it in such a way that the fasteners at the back can be
inserted into those on the side wall.
NOTE: the sauna panels are made of wood.
( 42, detail 6) Insert the covering panel between the base
wall and the back support and install it in such a way that the
fasteners at the back can be inserted into those on the side wall.
NOTE: the sauna panels are made of wood.
( 42, detail 7) Position the lights behind the panels.
Installing the door glass
If the shower has a door, install the fixed glass and the
glass door; refer to the attached documentation.
( 43, detail 1-3) Insert the plastic rings in the upper and
lower holes in the glass.
( 43, detail 2-4) Assemble the lower and upper hinge, ap-
plying the plates from the inner side of the glass.
( 43, detail 5-6) Fit the vertical sealant and move the glass-
door near the fixed one.
( 43, details 7-8) If you have not already done so, attach
the lower support and insert the ball into the ball pin.
NOTE: with the HAMMAM, we recommend placing silicone
in the holes of the cover to which the hinge is attached.
( 43, details 9-10) Start to install the glass by inserting the
lower hinge on the support pin and apply the longer set screw.
Support the glass until it is correctly fixed to the hinge!
( 43, details 11-12-13-14-15) Keep the glass open, insert
the ball inside the hinge and then the support in the hinge.
Fix the upper support and then apply the longer set screw.
( 43, details 16-17) From the inner side, fully apply the cov-
ers to the plates.
( 44, details 1-2) Apply the magnet in the upper gasket of
each door, as indicated
(detail 3-4) Assemble the gaskets:
- upper
- lower
( 45, details 1-2) Apply the magnetic gaskets, to both the
door glass and the built-in glass, ensuring correct assembly di-
25