DWT ESP01-250 Manual Original página 22

on the tip 22 with the grooves in the hole 21� Rotate the
tip 22 as shown on figure 4.1.
• Connect the air hose 7 to the spray gun or the purge
nozzle 15� Place the tip 23 on the shank of the ac-
cessory by pre-aligning the grooves in the tip 23 with
the protrusions on the accessory� Rotate the tip 23 as
shown on figure 4.2.
• In order to disconnect, perform these steps in re-
verse order�
Initial operating
of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power
tool on / off
[ESP01-250]
Switching on:
Press and hold button 4�
Switching off:
Release button 4�
[ESP05-200 T]
Switching on:
Press and release on / off switch 9� In order to start
spraying material, press and hold button 4 on the spray
gun�
Switching off:
Release button 4, then press and release on / off
switch 9�
Design features
of the power tool
Sprayed material volume regulation (see fig. 5)
• Using regulator 6, you can adjust the volume of the
spayed material in order to get the desired work re-
sult�
• To decrease volume of the sprayed material, ro-
tate regulator 6 as shown in figure 5 (while spraying
material)� Note that the excessive decrease of the
sprayed material volume leads to poorer results of
treatment (insufficient impregnation, too thin a paint
layer, etc�)�
• To increase volume of the sprayed material, rotate
regulator 6 as shown in figure 5 (while spraying mate-
rial)� Note that an excessive increase of the sprayed
material volume results in drips on the treated surface
and overconsumption of the sprayed material�
Sprayed stream shape regulation (see fig. 6)
[ESP05-200 T]
You can adjust the shape of the sprayed stream by ro-
tating air cap 2 depending on the direction of the spray
gun's movement (see fig. 6.2-6.4).
• Loosen coupling nut 3 (see fig. 6.1).
• Turn air cap 2 to the desired position (see fig. 6.2-6.4).
• Tighten coupling nut 3�
Spray gun holder (see fig. 7)
[ESP05-200 T]
The holder 10 is designed to secure the spray gun
during the movement of the power tool or during the
breaks in the work process�
Install the holder 10 as shown on figure 7.1 (the fix-
tures on the lugs must click shut)� You can install the
holder 10 from different sides of the base unit 11�
To remove the holder 10, slightly pull the lugs and re-
move the holder as shown on figure 7.2.
Carrying belt (see fig. 7)
[ESP05-200 T]
To facilitate the transportation, as well as to provide
greater portability during the work, use the carrying
belt 14� Connect the belt 14 to the base unit 11 (see
fig. 7.3). If necessary, adjust the length of the belt 14 so
that make carrying the power tool easier�
on the power tool operation
Measurement of sprayed material viscosity (see
fig. 8)
The viscosity of the sprayed material should not ex-
ceed the maximum allowable value (see technical data
table)� Thicker materials should be diluted� Please
note! Always use an appropriate solvent, other-
wise the lumps will form that will result in clogging
the power tool.
Measure the viscosity using measuring funnel 12� The
temperature of the compound should be 20-22°С.
• Stir the compound thoroughly, immerse measuring
funnel 12 into it, and wait until it fills (see fig. 8).
• Lift measuring funnel 12 up and let the liquid flow
out. Measure the time of liquid flow out (DIN-s) of
measuring funnel 12 using a stop-watch (from the start
of the flowing-out to jet separation). Approximate rec-
ommended viscosity values for different materials are
given below:
• impregnating agents, varnishes, synthetic resins -
undiluted, 30 DIN-s max�;
• synthetic paints, transparent varnishes - 15-35
DIN-s;
• acrylic paint - 20-35 DIN-s;
• preservatives, pesticides, oils for wood - undilut-
ed, 35 DIN-s max�;
• disinfectant and cleaning agents, polishes - 35
DIN-s;
• car paint - 18-22 DIN-s�
• After you are done with the measurements, thor-
oughly clean measuring funnel 12 (using an appropri-
ate solvent)�
Surface preparation
• The treated surface must be cleaned, dried, and de-
greased�
• Glossy surfaces should be roughed (with sandpa-
per), dust removed, and the surface should be de-
greased�
• The surrounding surfaces that need protection
from precipitation of the "mist" of the sprayed mate-
rial should be covered with thick materials (paper, film,
etc�) and lined with adhesive tape, when necessary�
English
22
Recommendations