Planer Safety Warnings - Ryobi RAP1500G Manual De Utilización

EN
FR DE ES IT NL
sense and do not operate the tool when you are tired.
■ Check damaged parts. Before further use of tool, it
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any
other conditions that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced by an authorized service centre
unless otherwise indicated in this instruction manual.
Have defective switches replaced by an authorized
service centre. Do not use the tool if the switch does
not turn it on and off.
■ warning. The use of any accessory or attachment
other than the one recommended in this instruction
manual may present a risk of personal injury.
■ Have your tool repaired by a qualified person.
This electric tool complies with the relevant safety
rules. Repairs should only be carried out by qualified
persons using original spare parts otherwise this may
result in considerable danger to the user.

plAnER SAfEty wARninGS

■ Always wear eye and ear protection when operation
the machine.
■ Wear gloves when handling the cutter block and rough
material to reduce injuries from sharp edges.
■ Wear a face or dust mask if the operation is dusty.
■ Check to make sure all holding screws are tight before
starting machine.
■ Always stop the motor and disconnect from the power
source before making any adjustments.
■ Be sure all guards are in place before operation.
■ Read operator's manual thoroughly and familiarise
yourself with the machine before operation.
■ Do not force work through the machine. Allow the
planer to apply the proper feed rate.
■ Check feed rollers occasionally to be sure sawdust
and chips are not lodged between any components. If
rollers are not seated firmly, the feed rolls will not hold
timber firmly against the bed, allowing kickback.
■ Check and make sure the roller tables are on the same
plane with the work table when planing wood, and the
rollers can rotate freely when planing long workpieces.
■ Use the product to plane dry wood boards only.
■ Use sound timber, with no loose knots and as few tight
knots as possible.
■ Never stand directly in line with either the infeed or
outfeed sides. Always stand off to one side of the
machine.
PT DA SV FI NO RU
English
PL CS HU RO LV LT
■ Make sure the workpiece is free of nails, screws,
stones and other foreign objects which could damage
the blades.
■ Make sure the blades are attached correctly as
described in the instructions.
■ Use caution when handling the blades and cutterhead
assembly. The blades are sharp and can easily cut
your hand.
■ Allow the cutterhead to reach full speed before using.
■ Use the push stick instead of your hands to push the
workpiece when its end approaches the blades. The
push stick should be stored on the work table when
not in use.
■ Use blades which are well sharpened and maintained.
■ Use only cutting blades designed for the product.
■ Make sure the planer is securely mounted before
use. Pay extra attention to stability when planing long
workpieces.
■ Keep hands away from the blade when it is moving.
■ Do not make cuts deeper than 3mm (1/8").
■ Wear eye protection that meets your local safety
standards.
■ Do not remove jammed piece until the blade has
stopped and the power is OFF.
Never conduct the following operations:
■ Stopped work (i.e., any cut which does not involve
the full length of the workpiece)
■ Planing recesses, tenons or moulds
■ Planing badly bowed wood with inadequate contact
with the infeed table
Anti-KiCKbACK pAwlS
See figure 2.
■ An anti-kickback pawl is a device which, when properly
installed and maintained, is designed to stop the
workpiece from being kicked back toward the front of
the blade during a planer operation.
AvoiDinG KiCKbACK
■ Always use the correct blade depth setting.
Inspect the work for knots or nails before beginning a
cut. Knock out any loose knots with a hammer. Never
cut into a loose knot or nail.
■ Always use clean, sharp, and properly-set blades.
■ Never use planer with dull blades.
2
ET HR SL SK EL TR
wARninG
UK