Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Regular Agitene
and Super Agitene
®
odor and is far superior in cleaning ability than normal safety solvents.
Super Agitene also contains "HandEase," a lanolin formulation that
helps prevent skin irritation, plus seven other ingredients that make it a
unique cleaning fluid that cleans faster, more easily and lasts longer than
other cleaning fluids. Super Agitene also leaves a light rust retarding
film. Regular Agitene is a fast-drying, film-free cleaner which contains
Tergene, a detergent additive for better cleaning efficiency. Regular
Agitene is especially recommended for cleaning electrical parts since it
will not harm varnish and dries film free.
Never use a cleaning fluid that has a flash point below 104°F. Do NOT
use any FLAMMABLE fluids. See complete Warnings and Cautions on
page 2.
installatiOn anD OPeratiOn
Site Preparation
Before installing the Clean-O-Matic, careful consideration should be given
to the place of operation. Place unit on a smooth, level surface.
• The work area should be well ventilated.
• Provide adequate lighting in the work area to allow observation of
the cleaning process and the floor area around the machine.
• Be sure to allow adequate room to bring work to and from the
machine. Provide sufficient clearance around the machine for fluid
changeovers and servicing.
Installation Procedure
The Clean-O-Matic is very easily put into operation. After removing it
from its shipping carton, install the revolving casters supplied with units
so equipped (Models 300, 500), assemble handle to cover. Check to be
sure drain plug is tightened, fill with the desired amount of an appropriate
cleaning fluid (see Liquid Capacities, above) and insert the 3-prong plug
into the proper receptacle (see Electrical Characteristics, above). If using
an air motor, attach air line hose to valve on side of unit and the unit is
ready for use.
Before operating your Clean-O-Matic, read the following descriptions of its
features and benefits to maximize efficiency and longevity from your unit.
Automatic Safety Cover
Open the automatic Safety Cover (A) on your Clean-O-Matic and you will
notice that it lifts simply and easily with one hand. There is nothing to
connect or disconnect to open or close the cover.
Your Clean-O-Matic cover is equipped with a two-way gas spring that also
incorporates a fusible link (B). When open, the cover mechanism supports
the cover at a slightly forward angle. This angle is necessary to assure the
cover's fusible link (B) will operate in the unlikely event of fire in the tank.
In the event of a fire, the fusible link will melt at 165°F permitting the lid to
slam shut, reducing oxygen supply to the fire
Never leave the Clean-O-Matic unattended with parts in the tank which
would prevent the cover from closing completely in the event of a fire.
Always make sure that the cover remains in its correct, slightly tilted
forward position when open. Do NOT tamper with or remove the fusible
safety link. If the safety link breaks or is lost, replace immediately. Keep
the cover closed when the unit is not being used.
Work Shelves
Every Clean-O-Matic comes equipped with one perforated shelf (C) and
two telescoping shelves which serve as a freeboard barrier to help limit
VOC emissions. Your own cleaning needs will determine which position is
best for your operation.
Sludge Collector Trays (Optional Accessory)
Two or more "sludge trays" with side foam filters (D) are located at
the bottom of the tank. These trays collect the heavier contamination
produced by cleaning. To extend the life of the cleaning fluid, gently lift
out the trays after heavier materials have settled overnight. Remove and
properly dispose of any contaminants found in the trays. Replace the
sludge trays and commence operation. Regular cleaning of the sludge
trays will maximize cleaning fluid life and result in a more efficient cleaning
. Super Agitene has a mild, fresh
®
WARNING
CAUTION
CAUTION
I
H
C
F
D
K
operation.
Pumping Unit
The centrifugal pumping unit (E) supplied with the Clean-O-Matic is a
rugged "machine tool" quality unit that is a valuable aid in parts cleaning.
It is particularly useful in flushing away softened grease and grime after
parts have been soaked. As an added precaution, Model 300 has a mesh
screen placed over the intake of the pump. Be sure to keep this screen
free of contaminants, rags or other debris which would impede the pump's
intake of fluid.
Pump and Tank Agitation
To operate the pump and tank agitation after filling, flick the switch (F) on
the front of the Clean-O-Matic or turn valve for air. The yellow pilot light
should go on, indicating that the pump is running. The Selector Valve (G)
is located on the inside rear-right hand side of the tank. The Model 300
Selector Valve is two-position: one position directs fluid to the flexible
metal flush hose (H) and the spray hose (I), and the other position creates
the tank agitation. On Models 500 through 902, the Selector Valve (G)
permits use of tank agitation alone, the flush and spray hoses together,
or a combination of all three. The small valve on the flexible metal hose
(H) allows you to cut off flow to the flexible hose, directing all of the fluid
through the spray hose (I). Always direct flow into tank in such a way as to
avoid splashing. Never point spray nozzle at anyone.
When using the Tank Agitation setting, align parts in the tank so that the
maximum area of the parts or any cavities in the parts are exposed as
fully as possible to the fluid emitted from the jet nozzles. To minimize fluid
evaporation, keep the tank cover closed during agitation.
MaintenanCe
Cleaning
Your Clean-O-Matic is equipped with a filter that has a reusable screen
collector element (J). This screen collector should be cleaned at least
once a week, more often in heavy use, in order to help extend the life
of the cleaning fluid and increase cleaning efficiency. Periodically, an oil
filter cartridge can be placed in the filter canister in place of the screen
collector. (Use WIX 51076 or equal. For the location of your local WIX
dealer call WIX Customer Service: 704-864-6711.) Running the pump for
a few hours will pull more contaminants out of the fluid and help extend
fluid's usable life.
Since an oil filter cartridge will clog within a short time, use for only one
or two hours at the most. Removing as much excess dirt, chips and other
contaminants as possible before cleaning dirty parts will extend the life
of the cleaning fluid. Another way to extend fluid life is to use Graymills
Solvent Savers. Contact Customer Service for further details.
Changing Fluid
• Unplug electrical cord or remove air supply.
• Remove the flexible metal hose (H) from its bracket at the rear of
the tank. Remove the fluid from the tank by placing nozzle over
side and into proper container. Remove drain plug (K) to drain
A
B
J
G
L
E
G-40
NOTE
CAUTION
3
Tabla de contenido
