Tabla de contenido
Idiomas disponibles
Idiomas disponibles
To memorize a transmitter using Mode II, when the programming pushbutton is accessible, proceed as follows.
Table "A9"
Memorization using Mode II with the programming pushbutton
1.
Press the programming pushbutton the number of times corresponding to the required
command (1 = On-Off, 2 = Hold-to-run, 3 = Timer1, 4 = Timer2).
2.
Check that the led emits the number of long flashes corresponding to the required
command.
3.
Within 10 seconds press the required key of the transmitter to be memorized for at
least 3 seconds.
4.
If the memorization procedure is successful, the led emits 3 long flashes.
Note. If there are other transmitters to be memorized, for the same command selected in point 1, repeat point 3 within a further 10 sec-
onds; otherwise if the command is different, repeat point 1; the memorization phase terminates if no new transmitters are received within a
10 second interval.
A new transmitter can easily be memorized with the same characteristics as that of the old one. The "new" transmitter will inherit the char-
acteristics of the old one, i.e. if the old transmitter was memorized in Mode 1, the new one will also function in Mode 1, if the old transmit-
ter was memorized in Mode II then the key of the new transmitter will be associated to the same command as that of the old one. For mem-
orization, proceed as follows.
Table "A10"
Memorizing other transmitters with a previously memorized transmitter
1.
Press and hold down the key to be memorized of the new transmitter for at
least 3 seconds, then release.
2.
Press and hold down the pre-memorized key of the old transmitter
(for at least 3 seconds) then release the key.
3.
Press and hold down the key to be memorized of the new transmitter
(for at least 3 seconds) then release the key.
4.
Press and hold down the pre-memorized key of the old transmitter
(for at least 3 seconds) then release the key.
4.3) Timers
The TT2L and TT2D control units allow you to program 2 independent timers: Timer1 and Timer2, for the automatic switching on and off of
the connected device after a set time. The set time is reset at each command. The switch-off time can be brought forward by keeping the
Timer command active for longer than 3 seconds or by sending an Off command. The factory settings for the 2 timers, restored in case of
complete memory clearing, are: Timer1 = 1 minute and Timer2 = 10 minutes. The switch-on time can be programmed from a minimum of 1
second to a maximum of 9 hours. In order to program the timers you need a transmitter, memorized in Mode II, to give the command to the
relevant timer. For programming, proceed according to the following instructions.
Table "A11"
Programming the timers with a transmitter in Mode II
1.
Press and hold down the transmitter key corresponding to the timer you wish to program;
the relay will activate (On).
2.
Keep the same key pressed; after about 3 seconds the relay will deactivate (Off).
3.
Continue holding down the same key until the relay activates again (after approx. 8 seconds);
time counting begins as of this moment. Release the key.
4.
When the time you wish to program has elapsed, press a key on a transmitter memorized in
the control unit to stop the time counting and deactivate the relay; 3 long flashes will signal
that the time has been memorized, followed by 1 or 2 short flashes indicating that the
programming operation pertains to either Timer1 or Timer2.
If you need to set the timers for a period of time exceeding one hour you should follow the quick programming steps described below. Dur-
ing quick programming, the time is counted in the following manner: 1 s = 1 min, 1 min = 1 h (e.g.: programming time = 3 min 45 s, device
activation = 3 h 45 min).
Table "A12"
Quick programming of timers using the programming pushbutton
1.
Press and hold down the programming pushbutton.
2.
Wait for the led to illuminate, then wait for it to turn off, followed by a flashing
sequence.
3.
Release the pushbutton precisely during the first (Timer1) or second (Timer2)
long flash; the relay will activate and the counting stage will begin.
When the time you wish to program has elapsed, press and hold down key ● for 1
4.
second to stop the time counting process and deactivate the relay; release the button
at the first of the 3 long flashes that signal the completion of the time memorization
procedure; these will be followed by 1 or 2 short flashes indicating that the programming
operation pertains to either Timer1 or Timer2.
Example
1-4
1-4
3s
Example
New
3s
Old
3s
New
3s
Old
3s
Example
3s
8s
Example
(
)
1s
1-2
GB
1-2
7
Tabla de contenido
