Replacing The Dust Bag - Hoover SILENT ENERGY Manual De Instrucciones

CLeANeR MAINTeNANCe

replacing the dust Bag

if the bag check indicator flashes please check and, if necessary, replace the bag [11].
1. Press the button [12] to open the cover and pull the bag collar to remove the bag. The
full dust bag should be disposed of correctly and carefully (p13).
2. Fold a new bag as shown on the bag and fit by inserting the collar into the bag holder
[13].
3. Close the cover.
remember: The bag check indicator may also flash if an obstruction has occurred. in this
case refer to 'Removing A blockage from the System'.
Cleaning the Lifetime Washable Filter
To maintain optimum performance of your cleaner, please wash the pre-motor filter after
each 5 bag changes.
remove the pre-motor filter [14]. press the latch at the top of the hepa pre-motor filter
frame to unlock it from the cleaner . Tilt then remove the filter from the cleaner. Wash it in
hand warm water, and allow it to dry thoroughly before replacing to the cleaner.
remember: Do not use hot water or detergents. in the unlikely event of the filters becoming
damaged, fit a Genuine hoover replacement. Do not try and use the product without a dust
bag or filter fitted.
removing a Blockage From the System
if the bag check indicator is illuminated or flashing [11]:
1. Check if the bag is full. If so refer to 'Replacing The dust bag'.
2. If it is not full, then;
A. Do the filters need cleaning? if so refer to 'Cleaning the Lifetime Washable Filter'.
b. Check if there is any other blockage in the system - Use a rod or a pole to remove
any blockage from the Teletube or flexible hose.
Warning - The bag check indicator will flash intermittently if the cleaner is used when full,
if there is a blockage or if the filters are dirty. if the cleaner is used for a significant period
of time with the bag check indicator continuously flashing, a thermal cut out will switch the
cleaner off to prevent overheating. The bag check indicator will remain lit once the cleaner
has switched off to signal that the thermal cut out has been activated. if this should happen,
then switch the cleaner off, unplug and correct the fault. it will take about 30 minutes for the
cut out to automatically reset.
0565 5338 Silent Energy im_15 lang.indd 2
ACCeSSORIeS
please see the model specification on the packaging label for inclusion of accessories to
individual models. All accessories can be purchased separately from hoover. (See hoover
Spares and Consumable section).
All accessories can be fitted to the end of the hose or the end of the telescopic tube.
3 in 1 tool – Combines several functions in one, the 3 in 1 tool can be connected as a
dusting brush/ furniture nozzle [15], with maximum flexibility by the rotating body [16].
Alternatively the 3 in 1 tool can be connected as a crevice tool [17]. The 3 in 1 tool can be
stored neatly underneath the hose handle [18].
Crevice tool – for corners and hard to reach areas.
Furniture nozzle – for soft furniture and fabrics. [19]
dusting Brush – for bookshelves, frames, keyboards and other delicate areas [19]. To
extend the brushes push the button on the body of the tool.
parquet Caresse nozzle*– For parquet floors and other delicate floors. [20]
allergen remover turbo Brush* – Use the turbo nozzle for deep cleaning on carpets.
[21]
pet hair remover mini turbo Brush* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. [22]
allergen remover mini turbo Brush with Silver ion* - for anti bacterial cleaning. [23]
important: Do not use the turbo and mini turbo nozzles on rugs with long fringes, animal
hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush
is rotating.
USEr ChECKLiST
Should you have a problem with the product, complete this simple user checklist
before calling your local Hoover service.
• is there a working electricity supply to the cleaner? please check with another electrical
appliance
• is the dust bag over-filled? please refer to 'Cleaner maintenance'
• is the Filter blocked? please refer to 'Cleaning the lifetime washable filter'
• is the hose or nozzle blocked? please refer to 'removing a blockage from the
system'
• has the cleaner overheated? if so, it will take approximately 30 minutes to automatically
reset
•
2
gB
13/03/2009 09:34:31