Enlaces rápidos

Quick Start Guide
CMS 801 Series
CMS 801 SUB BM/CMS 801 SUB PI
8" Compact Ceiling Mounted Subwoofer for Installation Applications (Blind Mount)/(Pre-Install)
CMS 801 PI 8 OHM BACKCAN
Back Can for CMS 801 PI Series Ceiling Loudspeakers (Pre-Install)
loading

Resumen de contenidos para Tannoy CMS 801 Serie

  • Página 1 Quick Start Guide CMS 801 Series CMS 801 SUB BM/CMS 801 SUB PI 8" Compact Ceiling Mounted Subwoofer for Installation Applications (Blind Mount)/(Pre-Install) CMS 801 PI 8 OHM BACKCAN Back Can for CMS 801 PI Series Ceiling Loudspeakers (Pre-Install)
  • Página 2 11. Use únicamente los dispositivos o accesorios Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, por un técnico cualificado. manufacturer, or sold with cualquier persona por confiar total o parcialmente en...
  • Página 3: Wichtige Sicherheitshinweise

    Ce symbol signale les consignes et des surfaces de oder eingetragene Warenzeichen der Music Tribe Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, Im Innern des Geräts befinden sich keine vom Benutzer oder im Lieferumfang d’utilisation et d’ e ntre ! Tien importantes travail recommandés...
  • Página 4: Safety Notices

    Every TANNOY product and accessory is carefully inspected before packing. After unpacking, please inspect your product to make sure no damage has occurred in de saída da unidade. Certifique-se de que o cabo eléctrico 21.
  • Página 5 CMS 801 Series Quick Start Guide Product Feature Identifi cation Accessories Each product is supplied with the following accessories as standard: Fig 1.1: The blind-mount (BM) models come with a pre-fitted back can Tuning Port Euro Type Connector Screws for mounting wings C-Ring Tile bridge kit...
  • Página 6 4. Slide the speaker assembly through the hole and turn the screws to extend the mounting wings. Tighten the screws until a fi rm grip is achieved. If using a power driver, TANNOY recommends a torque setting of 1.5 Nm. DO NOT OVERTIGHTEN! 4.
  • Página 7 Instructions for Optional Pre-Installation Back can (Pi Models Only): An optional plaster (mud) ring bracket is available from TANNOY. This bracket is designed to be pre-installed into newly An optional pre-install back can is available for all pi (pre-install) models. This back can is designed to be pre-installed into newly constructed, non-suspended ceilings.
  • Página 8 CMS 801 Series Quick Start Guide Wiring And Setting Up: CMS 801 sub BM Dimensions: Template hole cutout size: 295 mm 1. Open the wiring cover at the back of the speaker can to access the Euro type connector plug and socket. 286.4 327.8 310.5...
  • Página 9: Technical Specifications

    (3) Long term power handling capacity as defi ned in EIA - 426B test A full range of measurements, performance data, and Ease™ Data can be downloaded from tannoy.com Transducers TANNOY operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifi cations, which TANNOY reserves the right to alter without prior notice. Low frequency Please verify the latest specifi cations when dealing with critical applications 1x 200 mm (8.00") long throw woofer with multi fi bre paper pulp cone...
  • Página 10 Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfi ller for your country listed under “Support” at tannoy.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support”...

Este manual también es adecuado para:

Cms 801 sub bmCms 801 sub piCms 801 pi 8 ohm backcan