Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ADDITIONAL SAFETY INSTRUCTIONS
Do not use Type 11 (flaring cup) wheels on this tool.
•
Using inappropriate accessories can result in injury.
Always use side handle. Tighten the handle
•
securely. The side handle should always be used to
maintain control of the tool at all times.
Use clamps or another practical way to secure and
•
support the work piece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
•
Always keep the guard screw attached on the guard.
PERSONAL SAFETY
• No children or pregnant women should enter the work
rea where the paint sanding is being done until all
cleanup is completed.
• A dust mask or respirator should be worn by all persons
entering the work area. The filter should be replaced
daily or whenever the wearer has difficulty breathing.
NOTE: only those dust masks suitable for working with lead
paint dust and fumes should be used. Ordinary painting
masks do not offer this protection. See your local hardware
dealer for the NIOSH approved proper mask.
ENVIRONMENTAL SAFETY
• Paint should be removed in such a manner as to
minimize the amount of dust generated.
• Areas where paint removal is occurring should be
sealed with plastic sheeting of 4 mils thickness.
• Sanding should be done in a manner to reduce tracking
of paint dust outside the work area.
RESIDUAL RISKS
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
– Impairment of hearing
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
– Risk of dust from hazardous substances.
ELECTRICAL SAFETY
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
WARNING! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by STANLEY, the
warranty will not be valid.
USING AN EXTENSION CABLE
If it is necessary to use an extension cable, please use an
approved extension cable that fits the tool's power input
specifications. The minimum cross-sectional area of the
(Original Instructions) ENGLISH
conducting wire is 1.5 sq. mm. Cables should be untangled
before reeling up.
Cable cross-sectional
area (mm
)
2
0.75
1.00
1.50
2.50
4.00
Cable length (m)
Voltage
Amperes
110-127
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0 20
220-240
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0 20
LABELS ON TOOL
The label on your tool may include the following symbols:
WARNING! To reduce the risk of injury, the
user must read the instruction manual before
use.
Wear safety glasses or goggles.
Wear ear protection.
Wear a dust mask.
V
Volts
A
Amperes
Cable rated current
(Ampere)
6
10
15
20
25
7.5 15
25
30
45
Cable rated current (Ampere)
6
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
25
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
25
Direct Current
n
Rated speed
60
10
15
20
25
-
-
6
6
15
15
20
-
27
Tabla de contenido
