Stanley SS30 Manual De Instrucciones página 19

3. Reattach the dust bag back onto the outlet and lock
into place by turning the dust bag collar clockwise.
USE
WARNING! Always wear gloves when you change
accessories. The exposed metal parts on the tool and
accessory may become extremely hot during operation.
Please operate tool with normal load. Do not overload. Do
not abuse the tool, please refer instruction manual to use
the tool correctly.
WARNING! Let the tool work at its own pace. Do not
overload.
WARNING! Always observe the safety instructions and
applicable regulations.
WARNING! To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories.
WARNING:
♦ Make sure all materials to be sanded are well secured.
♦ Apply only a gentle pressure to the workpiece. Excessive
pressure does not improve the sanding effect, but only
results in an increased load on the machine and causes
the abrasive to tear.
♦ Avoid overloading.
WARNING! Do not sand magnesium.
Notice: If you wrap the cord around the tool when you store
it, leave a generous loop of cord such that the cord guard
does not bend.
This helps prevent premature cord failure.
Proper Hand Position (FIG. D)
WARNING: To reduce the risk of serious personal injury,
always use proper hand position as shown.
WARNING: To reduce the risk of serious personal injury,
always hold securely in anticipation of a sudden reaction.
Proper hand position requires either one hand on the sander
body (10) or one hand on the main grip (11) as shown.
Switching On and Off (FIG. A)
Set the sanding speed using the electronic speed control
dial (2).
To switch the tool on, set the on/off switch to position I.
To switch the tool off, set the on/off switch to position O.
Sanding
Start with the coarsest grit size.
As the tool produces small abrasion marks in all directions, it is not necessary to sand along the grain.
Check your work at short intervals.
Always switch off the tool when work is finished and before
unplugging.
Hints for optimum use
♦ Do not exert too much pressure on the tool.
♦ Regularly check the condition of the sanding paper.
♦ Replace sanding paper when necessary.
♦ When sanding new layers of paint before applying
another layer, use extra fine grit.
♦ On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to a
fine grit for a smooth finish.
♦ Consult your retailer for more information on available
accessories.
WARNING! Do not use this tool to mix or pump
easily combustible or explosive fluids (benzine,
alcohol, etc.). Do not mix or stir inflammable liquids
labelled accordingly.
Accessories
The performance of your tool depends on the accessory
used. STANLEY accessories are engineered to high quality
standards and designed to enhance the performance of
your tool. By using these accessories you will get the very
best from your tool.
MAINTENANCE
Your STANLEY corded/cordless appliance/tool has been
designed to operate over a long period of time with a
minimum of maintenance. To ensure satisfactory operations,
the tool must be maintained and cleaned regularly
WARNING: To reduce the risk of injury, turn
unit off and disconnect machine from power
source before installing and removing accessories,
before adjusting or changing set-ups or when making
repairs. Be sure the trigger switch is in the OFF position.
An accidental start-up can cause injury.
♦ This machine is not user-serviceable. If problems occur
contact an authorised repair agent.
♦ The tool will automatically switch off when the carbon
brushes are worn.
WARNING! Before performing any maintenance on corded/
cordless power tools:
♦ Switch off and unplug the appliance/tool.
♦ Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
♦ Or run the battery down completely if it is integral and
then switch off.
♦ Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
♦ Regularly clean the ventilation slots in your appliance/
tool/ charger using a soft brush or dry cloth.
♦ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
♦ Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Lubrication
Your power tool requires no additional lubrication.
Accessories and attachments used must be
regularly lubrication around the SDS Plus fitment.
ENGLISH (
Original Instructions)
19