Important Remarks; Compliance With Legislation; Description Of The Control Unit - V2 EASY Manual Del Usuario

IMPORTANT REMARKS

For any installation problems please contact
V2 S.p.A. TEL. (+39) 01 72 81 24 11
V2 S.p.A. has the right to modify the product without
previous notice; it also declines any responsibility for
damage or injury to people or things caused by improper
use or wrong installation.
Please read this handbook very carefully before
installing and programming your City4 control unit.
• This handbook is only for qualified technicians, specialized
in installations and automations.
• The content of this handbook does not concern the
end user.
• Every programming and/or every maintenance service
should be done only by qualified technicians.
AUTOMATION MUST BE IMPLEMENTED IN COMPLIANCE
WITH THE EUROPEAN REGULATIONS IN FORCE:
EN 60204-1 (Machinery safety. electrical equipment of
machines, part 1: general rules)
EN 12445 (Safe use of automated locking devices,
test methods)
EN 12453 (Safe use of automated locking devices,
requirements)
• The installer must provide for a device (es. magnetotermical
switch) ensuring the omnipolar sectioning of the equipment
from the power supply.
The standards require a separation of the contacts
of at least 3 mm in each pole (EN 60335-1).
• After making connections on the terminal board, use one
hose clamp to fix dangerous voltage wires near the terminal
board and another hose clamp to fix safety low voltage wires
used for accessories connection; this way, in case of
accidental detachment of a conducting wire, dangerous
voltage parts will not come into contact with safety low
voltage ones.
• The plastic case has an IP55 insulation; to connect flexible
or rigid pipes, use pipefittings having the same insulation
level.
• Installation requires mechanical and electrical skills,
therefore it shall be carried out by qualified personnel only,
who can issue the Compliance Certificate concerning the
whole installation (EEC Machine Directive 89/392, Annex IIA).
• The automated vehicular gates shall comply with the
following rules: EN 12453, EN 12445, EN 12978 as well
as any local rule in force.
• Also the automation upstream electric system shall comply
with the laws and rules in force and be carried out
workmanlike.
• The door thrust force adjustment shall be measured
by means of a proper tool and adjusted according to
the max. limits, alowed by EN 12453.
• We recommend use an emergency button, to be installed by
the automation (connected to the control unit STOP input)
so that the gate may be immediately stopped in case of
danger.
• Always remember to connect the earth according to
current standards (EN 60335-1, EN 60204-1).

COMPLIANCE WITH LEGISLATION

V2 S.p.A. confirms that EASY comply with the basic
requirements in the following directives:
- 89/336/CEE (EMC Directive according to EN 61000-6-2,
EN 61000-6-3 standards)
- 73/23/CEE (Low Voltage Directive according to EN 60335-1
standards)
- 99/05/CEE (Radio Directive according to EN 301,489-3
standards)
Racconigi, lì 20/04/2006
V2 S.p.A. legal representative
A.Livio Costamagna

DESCRIPTION OF THE CONTROL UNIT

The EASY digital control unit is an innovative V2 product that
guarantees safety and reliability for the automation of winding
shutters, overhead doors and industrial sectionals.
The EASY design focused on creating a product meeting all
requirements, obtaining an extremely versatile control unit,
satisfy all the needs of a practical, efficient installation.
• 230 VAC output for 1 single-phase motor
• 230 VAC output for flashing light or timed courtesy light
• Input for key switch or pushbutton (START)
• Input for separate UP/DOWN commands
• Input for safety pushbutton (STOP)
• Input for safety photocell with automatic operating test
(PHOTO)
• Input for safety edge (mechanic or electronic) with
automatic operating test (EDGE)
• Input for fire emergency (FIRE)
• Monitoring the inputs using LED
• Operating logic and working times that can be
programmed using the programming key and 8 LEDs
• Possibility of operating in DEAD MAN mode
EASY-RI
• Fitted 433.92 MHz radio receiver
• Possibility of saving 18 433.92 MHz Personal Pass
transmitters.
• Allows the total deletion of stored codes
EASY-RM
• Fast connector to insert a Mr1 series receiver.
EASY-CRI
• Input for optical safety edge with 24V direct current power
supply and adjustment of the power of the transmitter.
WARNING: use only FEEL optical safety edges (see
V2 catalogue)
• Fitted 433.92 MHz radio receiver
• Possibility of saving 18 433.92 MHz Personal Pass
transmitters.
• Allows the total deletion of stored codes
9