Declaration Of Performance - Novoferm TH80 Manual De Montaje, Usuario Y Mantenimiento

Unique identification code of the product-type: Roller Shutter
1.
2 Type, batch or serial number or any other element allowing identification of the construction product as required pursuant to Article 11(4): see CE mark
Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: manual or power
3.
operated door, intended for installation in areas in the reach of persons, and for which the main intended uses are giving safe access for goods and vehicles
accompanied or driven by persons in industrial, commercial or residential premises.
4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required pursuant to Article 11(5):
5. -
System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 3
6.
7. In case of the declaration of performance concerning a construction product covered by a harmonised standard:
The Notified Body, NB No.: 0044 TÜV Nord Cert GmbH, D-45141 Essen, IFT Rosenheim, D-83026 Rosenheim conducted product testing based on type approval and
issued: Test reports detailing the performance characteristics of the product. The company's in-house production control complies with the requirements of EN
ISO9001:2008.
8. -
9. Declared performance:
Key characteristics
Watertightness
Release of dangerous substances
Resistance to wind loads
Thermal resistance
Air permeability
Safe opening (doors that move vertically)
Definition of geometry of glas components
Mechanical resistance and stability
Operating forces (power operated doors)
Durability of watertightness, thermal resistance and air permeability against degradation
10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9 and, when combined with the prescribed
GFA SI 17.15, SI 25.15, SI 40.15, SI 55.15, SI 65.10, SI 75.15, SI 100.10, SI 140.7, SI 25.80-40 door operators, complies with the pertinent provisions of the EC Machinery Directive (Directive 2006/42/EC) / harmonized technical specification: EN 12453:2000
o
the EC Low Voltage Directive (Directive 2006/95/EC) / harmonized technical specification: EN 60335-1:2010, EN 60335-2-95:2004
o
the EMC Directive (Directive 2004/108/EC) / harmonized technical specification: EN 61000-6-2:2005, EN 61000-6-3:2007
o
This conformity has been confirmed by the Notified Body indicated in number 7.
This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.
Signed for and on behalf of the manufacturer by:
Frank Wiedenmaier, Member of the Management Board / COO
Waardenburg, 07.03.2013
......................................................................................................................................................
We hereby confirm compliance with the manufacturer's specifications.
Place, Date:
Please keep these assembly, operating and maintenance instructions as long as you use the product!
DECLARATION OF PERFORMANCE No. 1000-CPR-2015
Novoferm Nederland BV
Novoferm Nederland BV
Industrieweg 9
Industrieweg 9
4181 CA Waardenburg, Nederland
4181 CA Waardenburg, Nederland
Tel.: +31(0)418 654700 / Fax: +31(0)88 8888505
Tel.: +31(0)418 654700 / Fax: +31(0)88 8888505
E-mail: [email protected]
E-mail: [email protected]
Signature:
Name and address of installation firm
Performance Harmonized technical specification
see CE mark
NPD
see CE mark
see CE mark
see CE mark
EN 13241-1:2003+A1:2011
confirmed
NPD
confirmed
confirmed
see CE mark
______________________
Frank Wiedenmaier, COO Novoferm GmbH
Signature:
EN
EN
7