Double Sided Installation 11 - EcoSmart Fire FLEX18DB Manual De Instalación

ENGLISH
double sided
installation
Equipment required: Power Drill, Screwdriver, Level, Hand Trowel for
Plaster, Silicone Gun, Caulk Gun
1. Construct a main wall framework with the opening size shown in
Table D. The base of the frame can be a solid bench/platform, which
will assist in leveling up the appliance when in position.
WarninG: double-sided appliances cannot be inserted into a
one-way cavity wall, it must be a two-way cavity where the glass
on both sides is free from obstructions. do not apply pressure
or materials to the glass. double sided appliances are designed
as wall divider inserts. If you do not comply with this installation
instruction the wall could overheat and catch fire.
Table D: Framework Opening Sizes
Physical appliance dimensions should be verified against cut out dimensions BEFORE
installation begins to confirm tolerances align.
W d h Weight*
aPPlianCe
mm [in] mm [in] mm [in] kg [lbs]
Flex18dB 488 [19.2] 349 [13.6] 730 [28.7] 26.5 [58.3]
Flex32dB 46.6 [102.5]
922 [36.3] 349 [13.6] 730 [28.7]
Flex42dB 1177 [46.3] 349 [13.6] 730 [28.7] 61.4 [135.1]
Flex50dB 1380 [54.3] 349 [13.6] 730 [28.7] 70.8 [155.8]
Flex50dB.Bx 1380 [54.3] 349 [13.6] 730 [28.7] 70 [154]
Flex60dB.Bx 1634 [64.3] 349 [13.6] 730 [28.7] 83.3 [183.3]
Flex68dB 95.5 [210.1]
1840 [72.4] 349 [13.6] 730 [28.7]
Flex68dB.Bx 1840 [72.4] 349 [13.6] 730 [28.7] 83.7 [184.1]
Flex68dB.Bx2 94.8 [208.6]
1840 [72.4] 349 [13.6] 730 [28.7]
Flex78dB.Bx2 2090 [82.3] 349 [13.6] 730 [28.7] 106.2 [233.6]
Flex86dB 2300 [90.5] 349 [13.6] 730 [28.7] 102.3 [225.1]
Flex86dB.Bx 2300 [90.5] 349 [13.6] 730 [28.7] 124.5 [273.9]
Flex86dB.Bx2 2300 [90.5] 349 [13.6] 730 [28.7] 108.5 [238.7]
Flex104dB
2760 [108.7] 349 [13.6] 730 [28.7] 145.7 [320.5]
Flex104dB.Bx 2760 [108.7] 349 [13.6] 730 [28.7] 127.1 [279.6]
Flex104dB.Bx2 142 [312]
2760 [108.7] 349 [13.6] 730 [28.7]
Flex122dB 3220 [126.7] 349 [13.6] 730 [28.7] 145.6 [320.3]
Flex122dB.Bx 170.1 [374.2]
3220 [126.7] 349 [13.6] 730 [28.7]
Flex122dB.Bx2 3220 [126.7] 349 [13.6] 730 [28.7] 151.9 [334.2]
Flex140dB.Bx 3680 [144.9] 349 [13.6] 730 [28.7] 170.4 [374.9]
Flex140dB.Bx2 3680 [144.9] 349 [13.6] 730 [28.7] 192.9 [424.4]
Flex158dB 4140 [163] 349 [13.6] 730 [28.7] 226.8 [499]
Flex158dB.Bx2
4140 [163] 349 [13.6] 730 [28.7] 195.2 [429.4]
* Appliance weight includes burner/s (dry weight excluding fuel), glass charcoal and glass. It
does NOT include glass charcoal for side boxes.
iMPortant: the framing above the appliance must be self-
supporting. the appliance is not load-bearing.
www.ecosmartfire.com
2. Remove the extension flange from the firebox so that both sides are
the same height. This will help make sliding the firebox into the frame
easier. Pay attention not to lose the screws, they will be needed again
when the flange is re-installed.
3. Slide the appliance inside the framing cavity (the bottom tray can sit
directly on top of the frame). The appliance is shipped with red stability
bracket(s) installed on the open side(s) to keep the appliance square while
in transport and during installation. Keep the bracket(s) on while framing
up the setting to assist in minimising movement of the appliance.
FRONT VIEW
4. Align the flange extension panel with the threaded holes on the
appliance. Screw it into place using the included screws (bottom row
onto appliance, top row onto framing material) to secure it into position.
BACK VIEW
5. Fix the appliance to the framework with screws using the existing
mounting holes on the appliance flanges. Make sure that the
appliance is level before securing it in place.
ENGLISH
double sided
installation
6. Remove the red stability bracket(s).
7. Complete the construction by finishing the wall paneling around the
appliance. (See section on FinishinG instrUCtions and ensure that
you fully understand where non combustible materials must be used.)
8. Place the burner into position.
9. Remove the dust protective tape that covers the windscreen
mounting slots.
10. If your appliance includes a decorative box on the left / right or
both, insert the internal glass panel by feeding the glass upwards
into the slot then pushing down into the positioned clips.
*Decorative logs must NOT be placed directly over an open flame.
They are designed to sit near heat but not over flames.
11. Install the windscreen by inserting the two ends into appropriate
slots in the appliance. Use a small amount of pressure to push the
windscreen in place until it bottoms out into the hidden glass clips.
Repeat the same for the back side windscreen.
WARNING: The glass used is toughened glass - which means it is
stronger than normal glass. Importantly, even though it is stronger,
toughened glass still has weaknesses. The corners and sides are
specific pressure points where it is more fragile and can break if care
is not taken. Glass breaks into many small pieces. Take care to avoid
cuts. We recommend you wear protective gloves when handling glass.
12. Spread the glass charcoal evenly around the appliance tray.
CAUTION: Make sure the burner lid is closed. Keep the glass
charcoal away from the burner flange to avoid glass charcoal from
accidentally going into the burner chamber. Be careful not to scratch
the burner.
© Copyright 2004 - 2019 MAD Design Group. All rights reserved. V0719