Right Corner Installation - EcoSmart Fire FLEX18DB Manual De Instalación

ENGLISH
left Corner & right Corner
installation
Equipment required: Power Drill, Screwdriver, Level, Hand Trowel for
Plaster, Silicone Gun, Caulk Gun
1. Construct a main wall framework leaving an opening as shown in
Table B. The base of the frame can be a solid bench/platform, which
will assist in leveling up the appliance when in position.
NOTE: Illustrations are of Left Corner installation.
Table B: Framework Opening Sizes
Physical appliance dimensions should be verified against cut out dimensions BEFORE
installation begins to confirm tolerances align.
aPPlianCe W d h Weight*
(lC & rC) mm [in] mm [in] mm [in] kg [lbs]
Flex18lC [14.4] 33 [72.6]
470 [18.5] 365 730 [28.7]
Flex32lC 902 [35.5] 365 [14.4] 730 [28.7] 48.8 [107.4]
Flex42lC 1157 [45.5] [14.4] 730 [28.7] 63.3 [139.3]
365
Flex50lC 1362 [53.6] 365 [14.4] 730 [28.7] 71.6k [157.5]
Flex50lC.Bx 1362 [53.6] [14.4] 730 [28.7] 73.1 [160.8]
365
Flex60lC.Bx
1617 [63.7] 365 [14.4] 730 [28.7] 87.1 [191.6]
Flex68lC 1822 [71.7] 365 [14.4] 730 [28.7] 100.3 [220.7]
Flex68lC.Bx [14.4] 95.3 [209.7]
1822 [71.7] 365 730 [28.7]
Flex68lC.Bx2 1822 [71.7] 365 [14.4] 730 [28.7] 97kg [213.4]
Flex78lC.Bx2 [14.4] 111 [244.2]
2077 [81.8] 365 730 [28.7]
Flex86lC 2282 [89.8] 365 [14.4] 730 [28.7] 121.7 [267.7]
Flex86lC.Bx 2282 [89.8] [14.4] 730 [28.7] 122.6 [269.7]
365
Flex86lC.Bx2 2282 [89.8] 365 [14.4] 730 [28.7] 119 [261.8]
Flex104lC 2742 [107.9] [14.4] 730 [28.7] 149.5 [328.9]
365
Flex104lC.Bx
2742 [107.9] 365 [14.4] 730 [28.7] 145.4 [319.9]
Flex104lC.Bx2 2742 [107.9] 365 [14.4] 730 [28.7] 146.9 [323.2]
Flex122lC [14.4] 171.7 [377.7]
3202 [126.1] 365 730 [28.7]
Flex122lC.Bx 3202 [126.1] 365 [14.4] 730 [28.7] 173.4 [381.5]
Flex122lC.Bx2 [14.4] 169.1 [372]
3202 [126.1] 365 730 [28.7]
Flex140lC.Bx 3662 [144.2] 365 [14.4] 730 [28.7] 197.1 [433.6]
Flex140lC.Bx2 3662 [144.2] [14.4] 730 [28.7] 195.4 [429.9]
365
Flex158lC 4122 [162.3] 365 [14.4] 730 [28.7] 225.5 [496.1]
Flex158lC.Bx2 4122 [162.3] 365 [14.4] 730 [28.7] 219.1 [482]
* Appliance weight includes burner/s (dry weight excluding fuel), glass charcoal and glass. It
does NOT include glass charcoal for side boxes.
iMPortant: the framing above the appliance must be self-
supporting. the appliance is not load-bearing.
www.ecosmartfire.com
2. Slide the appliance inside the framing cavity (the base of the
appliance can sit directly on top of the 2 x 4 framing material). The
appliance is shipped with red stability bracket(s) installed on the open
side(s) to keep the appliance square while in transport and during
installation. Keep the bracket(s) on while framing up the setting to
assist in minimising movement of the appliance. Align the top corner
flange extension panel with the threaded holes on top shelf and
screw into place with the included screws
3. Secure the appliance to the framework using the existing mounting
holes on the appliance flanges. Make sure that the appliance is level
before securing it in place.
4. Remove the red safety bracket(s).
ENGLISH
left Corner & right Corner
installation
5. Complete the construction by finishing the wall paneling around the
appliance. (See section on FinishinG instrUCtions and ensure that
you fully understand where non combustible materials must be used.)
6. Place the burner into position.
7. Remove the dust protective tape that covers the windscreen
mounting slots.
8. If your appliance includes a decorative box on the left / right or both,
insert the internal glass panel by feeding the glass upwards into the
slot then pushing down into the positioned clips.
*Decorative logs must NOT be placed directly over an open flame.
They are designed to sit near heat but not over flames.
9. Insert the full height glass panel into one of the open end side by
inserting the glass into the opening at the top of the appliance, and
lowering it into the slots in the base until it bottoms out into place.
10. Install the windscreen by inserting the glass ends into the slots. Use
a small amount of pressure to push the windscreen in place until it
bottoms out into the hidden glass clips.
WARNING: The glass used is toughened glass - which means it is
stronger than normal glass. Importantly, even though it is stronger,
toughened glass still has weaknesses. The corners and sides are
specific pressure points where it is more fragile and can break if care
is not taken. Glass breaks into many small pieces. Take care to avoid
cuts. We recommend you wear protective gloves when handling glass.
11.Spread the glass charcoal evenly around the appliance tray.
CAUTION: Make sure the burner lid is closed. Keep the glass
charcoal away from the burner flange to avoid glass charcoal from
accidentally going into the burner chamber. Be careful not to scratch
the burner.
© Copyright 2004 - 2019 MAD Design Group. All rights reserved. V0719