Bay Installation - EcoSmart Fire FLEX18DB Manual De Instalación

ENGLISH
Bay
installation
Equipment required: Power Drill, Screwdriver, Level, Hand Trowel for
Plaster, Silicone Gun, Caulk Gun
1. Construct a main wall framework leaving an opening as shown in
Table C. The base of the frame can be a solid bench/platform, which
will assist in leveling up the appliance when in position.
Table C: Framework Opening Sizes
Physical appliance dimensions should be verified against cut out dimensions BEFORE
installation begins to confirm tolerances align.
W d h Weight*
aPPlianCe
mm [in] mm [in] mm [in] kg [lbs]
Flex18BY 460 [18.1] 365 [14.4] 730 [28.7] 40.7 [89.5]
Flex32BY [14.4] 51.9 [114.2]
892 [35.1] 365 730 [28.7]
Flex42BY 1147 [45.2] 365 [14.4] 730 [28.7] 66.5 [146.3]
Flex50BY [14.4] 730 [28.7] 71.8 [158]
1352 [53.2] 365
Flex50BY.Bx 1353 [53.3] 365 [14.4] 730 [28.7] 76.2 [167.6]
Flex60BY.Bx 1608 [63.3] [14.4] 730 [28.7] 90.3 [198.7]
365
Flex68BY 1813 [71.4] 365 [14.4] 730 [28.7] 103.6 [227.9]
Flex68BY.Bx 1813 [71.4] 365 [14.4] 730 [28.7] 95.5 [210.1]
Flex68BY.Bx2 [14.4] 100.2 [220.4]
1813 [71.4] 365 730 [28.7]
Flex78BY.Bx2 2068 [81.4] 365 [14.4] 730 [28.7] 114 [250.8]
Flex86BY [14.4] 121.9 [268.2]
2272 [89.4] 365 730 [28.7]
Flex86BY.Bx 2272 [89.4] 365 [14.4] 730 [28.7] 125.9 [277]
Flex86BY.Bx2 2272 [89.4] [14.4] 730 [28.7] 119.2 [262.2]
365
Flex104BY 2733 [107.6] 365 [14.4] 730 [28.7] 152.9 [336.4]
Flex104BY.Bx 2733 [107.6] [14.4] 730 [28.7] 145.6 [320.3]
365
Flex104BY.Bx2
2733 [107.6] 365 [14.4] 730 [28.7] 150.1 [330.2]
Flex122BY 3193 [125.7] 365 [14.4] 730 [28.7] 171.9 [378.2]
Flex122BY.Bx [14.4] 176.7 [388.7]
3193 [125.7] 365 730 [28.7]
Flex122BY.Bx2 3193 [125.7] 365 [14.4] 730 [28.7] 169.3 [372.5]
Flex140BY.Bx [14.4] 195.6 [430.3]
3653 [143.8] 365 730 [28.7]
Flex140BY.Bx2 3653 [143.8] 365 [14.4] 730 [28.7] 200.3 [440.7]
Flex158BY 4113 [161.9] [14.4] 730 [28.7] 228.8 [503.4]
365
Flex158BY.Bx2 4113 [161.9] 365 [14.4] 730 [28.7] 219.3[482.5]
* Appliance weight includes burner/s (dry weight excluding fuel), glass charcoal and glass. It
does NOT include glass charcoal for side boxes.
MPortant: the framing above the appliance must be self-
supporting. the appliance is not load-bearing.
www.ecosmartfire.com
2. Slide the appliance inside the framing cavity (the base of the
appliance can sit directly on top of the 2 x 4 framing material). The
appliance is shipped with red stability bracket(s) installed on the open
side(s) to keep the appliance square while in transport and during
installation. Keep the bracket(s) on while framing up the setting to
assist in minimising movement of the appliance.
3. Ensure that the left and right side edges of the appliance are flush to the
frame-work studs.
4. Secure the appliance to the framework with screws using the
existing mounting holes on the appliance flanges. Make sure that the
appliance is level before securing it in place.
5. Remove the red stability brackets.
ENGLISH
Bay
installation
6. Complete the construction by finishing the wall paneling around the
appliance. (See section on FinishinG instrUCtions and ensure that
you fully understand where non combustible materials must be used.)
7. Place the burner into position.
8. Remove the dust protective tape that covers the windscreen
mounting slots.
9. If your appliance includes a decorative box on the left / right or both,
insert the internal glass panel by feeding the glass upwards into the
slot then pushing down into the positioned clips.
*Decorative logs must NOT be placed directly over an open flame.
They are designed to sit near heat but not over flames.
10. Insert the full height glass panel into one of the open end side by
inserting the glass into the opening at the top of the appliance, and
lowering it into the slots in the base until it bottoms out into place.
Repeat the same for the other side of the appliance.
11. Install the windscreen by inserting the two ends into appropriate
slots in the appliance. Use a small amount of pressure to push the
windscreen in place until it bottoms out into the hidden glass clips.
WARNING: The glass used is toughened glass - which means it is
stronger than normal glass. Importantly, even though it is stronger,
toughened glass still has weaknesses. The corners and sides are
specific pressure points where it is more fragile and can break if care
is not taken. Glass breaks into many small pieces. Take care to avoid
cuts. We recommend you wear protective gloves when handling glass.
12. Spread the glass charcoal evenly around the appliance tray.
CAUTION: Make sure the burner lid is closed. Keep the glass
charcoal away from the burner flange to avoid glass charcoal from
accidentally going into the burner chamber. Be careful not to scratch
the burner.
© Copyright 2004 - 2019 MAD Design Group. All rights reserved. V0719