Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Speedaire Operating Instructions & Parts Manual
Speedaire Gasoline Air
Compressor, Generator
and Welder
avoid equipment damage. Always
check the requirements of the tool
or appliance being used compared
to the rated output of the unit.
Read the instruction manual before
performing maintenance. Keep all air
E
vents clear. Keep the unit clean. DO
N
NOT spray with water. Periodically
G
check all fasteners and tighten, see the
periodic maintenance chart.
L
The following procedures must be
I
performed when stopping the unit for
S
maintenance or service.
H
1.
Turn off the unit.
2.
Disconnect spark plug wire from
engine.
3.
Open all drains.
4.
Wait for the unit to cool before
starting service.
Engine:
The engine for this unit is governed to
operate at speeds close to 3600 RPM
(60Hz) throughout the operating load
range.
Do not tamper with the governor-
mechanism, change the setting
experimentally, or push the throt-
tle open in an attempt to generate
more electrical current; Equipment
damage or personal injury may
result. Governor speed adjustment
should be made only by an autho-
rized servicing dealer.
Checking Engine Oil:
Check oil level before each operation-
and ensure that it is maintained per
engine manual.
Changing Engine Oil:
Change oil after the first 25 hours
ofoperation. Thereafter it should be
changed every 50 hours.
1.
Make sure the unit is on level
ground. Run the engine to warm
the oil.
2.
Stop the engine.
3.
Remove the oil drain plug.
CAUTION
Oil being drained may be hot. To re-
For Warranty and Service Call:
1-800-648-8478
®
duce the risk of burn injury, handle
with care. Dispose of used oil prop-
erly.4. Drain oil while engine is
warm, into a suitable container.
5.
Reinstall the oil drain plug.
6.
Remove oil gauge and refill with
new oil.
7.
Check the oil level as instructed in
the engine manual.
8.
Wipe up any spilled oil.
Air Cleaner:
RISK OF FIRE OR EXPLOSION. Do not
use gasoline or low flashing point
solvents to clean the element.
Clean the element in a well venti-
lated area. Ensure that no sparks or
flames are near the working area,
this includes any appliance with a
pilot light.
CAUTION
Never run the engine without
the air filter, serious damage can
result.
Check the air cleaner daily or before
starting the engine. Check for and cor-
rect heavy buildup of dirt and debris
along with loose or damaged compo-
nents.
1.
Unscrew the air cleaner cover and
remove the elements.
2.
Clean the element:
Foam Pre-Cleaner Element:
Wash the foam precleaner element
in warm water with detergent. Rinse
the foam pre-cleaner element thor-
oughly until all traces of detergent are
eliminated. Squeeze out excess water,
but do not wring. Allow the foam pre-
cleaner element to air dry. Saturate the
foam pre-cleaner element with new
engine oil. Squeeze out all excess oil.
DO NOT put engine oil on the foam
damper.
NOTE: Clean the foam pre-cleaner
element every 25 hours of operation
(more often under extremely dusty or
dirty condition)
Paper Air Cleaner Element:
Do notwash the paper element or use
8
pressurized air, as this will damage the
element. Clean by gently tapping the
element to remove dust. Replace the
element if damaged, bent or extremely
dirty. Handle new element carefully; do
not use if the sealing surfaces are bent
or damaged.
NOTE: Replace the paper element every
100 hours (more often under extremely
dusty conditions.)
3.
Reinstall the foam pre-cleaner
element and the paper air cleaner
element. Close air cleaner cover
and screw shut.
Idle Control Adjustment:
NOTE: The automatic idle speed is set
between 2640 and 2940 RPM.
The idle speed has been pre-set at the
factory and should rarely require read-
justment.
Erratic idle operation of the engine
usually indicates a need for carburetor
adjustment to provide a smooth idle.
The idle control will not function prop-
erly when the idle speed is below the
recommended limits or the carburetor
is improperly adjusted.
HAVE THE UNIT SERVICED BY AN
AUTHORIZED Customer Service
Representative.
GFCI Test Records:
As with any other safety devices, the
GFCIs supplied with these generators
must be checked every month to insure
that they are functioning properly. To
test the GFCIs, follow the instructions
and then enter the date of the test
below.
1.
With the generator running and
the idle control switch in the
"START" position, push the "TEST"
button. The "RESET" button should
pop out. This should result in the
power being off at both outlets of
the duplex receptacle.
fy this by plugging a test lamp into
each outlet.
If The Reset Button Does Not Pop
Out, Do Not Use The Receptacle(S).
See Authorized Customer Service
Representative For Service Immedi-
ately.
15D802
Veri-
Tabla de contenido
