Tabla de contenido
Idiomas disponibles
Idiomas disponibles
SETUP
PLEASE REFER TO THE EXPLODED VIEW DRAWING IN THIS MANUAL IN ORDER TO IDENTIFY PARTS.
1. Remove the 2-piece handle from box. Insert narrow portion of top section (30) into bottom section (32) and secure with the spring button.
2. Grease the inside of the handle yoke (35) and remove the handle set screw (33) from the yoke (35). Insert the handle (32) all the way in
the handle yoke (35) until it engages the universal joint assembly (36). Secure the handle (32) to the handle yoke (35) with the handle set
screw (33).
3. Air may become trapped in the hydraulic system during shipping and handling. Trapped air will affect the pumping performance
of the jack. If this occurs, follow the air purging procedure below:
a)
Remove the oil fill screw.
b)
With the lift arm assembly in its down position, look inside the oil fill screw hole. You should be able to see the top of the power unit's
pressure cylinder. The hydraulic fluid level should be no higher than the top of the cylinder. Correct the fluid level if it is not at the
proper height.
c)
Pump the jack against a load that is at least 500 lbs. (225 Kgs). After the load is raised, slightly turn the pump handle in a counter
clockwise rotation so the load is very slowly lowered. While the lift arm is lowering, quickly pump the handle 5 or 6 full incremental
pump strokes. After pumping, lower the lift arm to its full rest position.
d)
Install the oil fill screw. Rotate the handle in a clockwise rotation until tight and pump the lift arm to maximum height. If the pumping
condition has improved, repeat steps "a" through "d" until all of the air has been purged from the system.
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
IMPORTANT: Before attempting to raise any vehicle, check vehicle service manual for recommended lifting surfaces.
OPERATION:
1. To raise load: Close release valve tightly (by turning handle clockwise). DO NOT OVERTIGHTEN. Position jack under load so that saddle
will contact load firmly and load is centered so it cannot slip. Operate jack handle until saddle approaches the load. Once again, check
to see that saddle is correctly positioned. Raise load to desired height. Place jack stands of appropriate capacity under the vehicle. DO
NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR PLACING OR REMOVING JACK STANDS! Place jack stands at vehicle
manufacturer's recommended support areas that provide stable support for the raised vehicle. Once jack stands are positioned, open the
release valve VERY SLOWLY (by turning the handle counterclockwise). Lower the load to rest on the jack stands. Then, make sure that the
release valve on the jack is closed tightly (by turning the handle clockwise).
2. To lower load: Re-check to make sure release valve is tightly closed. Then, operate the jack handle until the load is raised enough to
remove the jack stands. DO NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR REMOVING THE JACK STANDS! Once jack
stands are removed, open release valve very slowly to lower the vehicle. Lower jack completely so that the vehicle is securely resting on
the ground and the jack no longer makes contact with vehicle.
CAUTION: Keep hands and feet away from the hinge mechanism of the jack.
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1.
Always store the jack in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust, or any
other harmful elements. The jack must be cleaned of water, snow, sand or grit before using.
2.
The jack must be lubricated periodically in order to prevent premature wearing of parts. A general purpose grease must be applied to all
zerk grease fittings, caster wheels, front axle, elevator arm, handle base pivot bolts, release mechanism and all other bearing surfaces.
Worn parts resulting from inadequate or no lubrication are not eligible for warranty consideration. See page 5 for lubrication instructions.
3.
It should not be necessary to refill or top off the reservoir with hydraulic fluid unless there is an external leak. An external leak requires
immediate repair which must be performed in a dirt-free environment by an authorized service center.
IMPORTANT: In order to prevent seal damage and jack failure, never use alcohol, hydraulic brake fluid, or transmission oil in the jack. Use
NAPA Hydraulic Jack Oil #765-1541.
4.
Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild soap solution to wash external surfaces of the
jack but not any moving hydraulic components.
5.
Inspect the jack before each use. Do not use the jack if any component is cracked, broken, bent, shows sign of damage or leaks
hydraulic fluid. Do not use the jack if it has loose or missing hardware or components, or is modified in any way. Take corrective
action before using the jack again.
6.
Any hydraulic repairs within the warranty period must be performed by an authorized service center.
791-6426
OPERATING MANUAL & PARTS LIST FOR 791-6426
3
03/23/12
Tabla de contenido
