gee, built with thick sheet metal - thickness 6 mm,
8 mm, 10 mm up to 20 mm – are laser cut and
welded. The brush plate is made from 15 mm
ship's sheet metal, with a surface treatment that
protects the plate and the paint for thousands of
hours in a saline fog. All screws are made with
stainless steel; the tanks (body) are made with 7-8
mm thick shockproof polyethylene. Everything is
simple and very strong, without any other compli-
cated designs.
- The battery compartment can house very large
batteries, which guarantees extended running
time.
- The suction motor is housed inside the machine,
thus reducing operating noise to a minimum.
- The recovery tank is very easy to clean due to the
lack of the characteristic difficult access points of
recovery tanks located in a lower position.
5.1.2
BATTERY
Regardless of the type of construction, battery
performances are indicated with the term capac-
ity, which always refers to a discharge period. An-
other important value is the number of possible
discharges. The capacity is expressed in amps per
hour (Ah), while the discharge period is generally
indicated as 20 hours (C20 or 20h, or not expressly
indicated) or 5 hours (C5 or 5h). The discharge/
charge cycles indicate the number of times that
the battery can hold a charge under the best con-
ditions, i.e. they indicate the useful battery service
life complying with all the necessary measures.
Therefore, the capacity of a battery varies depend-
ing on how fast it uses energy (current). That's why
there's such a variation in the capacity values ex-
pressed as C5 or C20. These factors must be taken
into account when comparing products available on
the market with our own.
This machine can be equipped with two types of
batteries that differ in terms of their construction
and features.
- Pb-Acid battery with tubular armoured modules:
the electrolyte level in each element must be peri-
odically checked!
If one element is no longer covered by the acid
solution it will oxidise in 24 hours, thus perma-
nently affecting that element's performance.
☞ Refer to the battery manual to avoid physical
damage and economic loss.
- Gel module battery: this type of battery is main-
tenance free and does not require special envi-
ronments for recharging (since it does not emit
any harmful gases); therefore, it is highly recom-
mended.
It should not be taken for granted that batter-
ies and battery chargers with the same technical
features as those we offer will produce the same
results. Only perfect compatibility between these
elements (Pb-Acid batteries, gel batteries and bat-
tery chargers) will safeguard the performances,
the service life, the safety and the economic value
invested.
5.1.3
BATTERY CHARGER
This type of high-frequency battery charger effi-
ciently charges batteries, extending their operating
and service life. In addition, because they can be
configured, it is a very versatile solution; the same
battery charger can be used for both Pb-Acid bat-
teries and for gel batteries.
It should not be taken for granted that batter-
ies and battery chargers with the same technical
features as those we offer will produce the same
results. Only perfect compatibility between these
elements (Pb-Acid batteries, gel batteries and bat-
tery chargers) will safeguard the performances,
the service life, the safety and the economic value
invested.
5.2
STRUCTURE AND FUNCTIONS
5.2.1
MACHINE
Photo A
1
Recovery tank
2
Operator's seat
3
Solution tank
4
Rear wheel
5
Bumper wheel
6
Splash guard
7
Front motorwheel
8
Traction control pedal
9
Electric components housing
10
Steering wheel
Photo B
1
Recovery water drain hose support hook
2
Recovery water tank drain
hose plug
3
Recovery water drain hose
4
Solution water tank filler plug
5
Suction hose
6
Rear cover
7
Blinker
Photo C
1
Knobs for suction cover opening
2
Anti-foam device
Photo D
1
Blinker
2
Suction hose seat
3
Floating switch
4
Rear cover
Photo E
1
Battery connector
2
Solution water dosing lever
Photo F
1
Suction motor switch
kruger.es
30