Panasonic S-22MU1E5 Instrucciones De Instalación página 27

Pana_indoor_336012_Eng.indb 47
■ 4-Way Cassette 60x60 Type (Y1 Type)
Checking the unit position
(1) Check that the ceiling hole is within this range:
600 × 600 mm
(2) Confirm that the positions of the indoor unit and the ceiling
are as shown in the diagram. If the positions of the ceiling
surface and unit do not match, air leakage, water leakage,
flap operation failure, or other problems may occur.
CAUTION
● Never place the panel face-down. Either hang it
vertically or place it on top of a projecting object.
Placing it face-down will damage the surface. (Fig. 7-12)
A must be within the range of 13 – 18 mm. (Fig. 7-12)
If not within this range, malfunction or other trouble may
occur.
Main unit
A
Ceiling opening
dimension
Ceiling side
● Do not touch the flap or apply force to it. (Fig. 7-13)
(This may cause flap malfunction.)
Flap
7-4. Before Installing the Ceiling Panel
(1) Remove the air-intake grille and air filter from the ceiling
panel.
a) Remove the 2 screws on the latch of the air-intake
grille. (Fig. 7-14) (Reattach the air-intake grille after
installation of the ceiling panel.)
Screw
Latch
b) Slide the air-intake grille catches in the direction shown
by the arrows 1 to open the grille. (Fig. 7-15)
Ceiling panel
Air-intake grille
1
1
Air-intake grille hinge
c) With the air-intake grille opened, remove the grille hinge
from the ceiling panel by sliding it in the direction shown
by the arrow 2. (Fig. 7-16)
2
Fig. 7-12
(2) Removing the corner cover.
a) Remove the screws on the corner and slide the latches
in the direction of the arrow 1 to disconnect the hinges
(3 locations). Then, remove the air-intake grille in the
direction of the arrow 2. (Fig. 7-17)
Corner cover
1
Fig. 7-13 Push
Ceiling panel
Corner cover
7-5. Installing the Ceiling Panel
The power must be turned ON in order to change the flap
angle. (Do not attempt to move the flap by hand. Doing so may
damage the flap.)
(1) Hang the temporary latches on the inside of the ceiling
panel to the receptacle on the unit to temporarily attach the
ceiling panel in place. (Fig. 7-18)
● The ceiling panel must be installed in the correct direction
relative to the unit. Align the REF. PIPE and DRAIN marks
on the ceiling panel corner with the correct positions on the
unit.
● To remove the ceiling panel, support the ceiling panel while
pressing the temporary latches toward the outside.
Fig. 7-14
(Fig. 7-18)
Temporary latches
Temporary
latch
(2) Align the panel installation holes and the unit screw holes.
49
2011/01/12 13:56:03 Pana_indoor_336012_Eng.indb 48
(3) Tighten the supplied washer head screws at the 4 panel
installation locations so that the panel is attached tightly to
the unit. (Fig. 7-19)
Refrigerant tubing joint
Fig. 7-15
Ceiling panel
Washer head screws
(4) Check that the panel is attached tightly to the ceiling.
● At this time, make sure that there are no gaps between the
unit and the ceiling panel, or between the ceiling panel and
the ceiling surface. (Fig. 7-20)
Fig. 7-16
Main unit
Ceiling surface
2
● If there is a gap between the panel and the ceiling, leave
the ceiling panel attached and make fine adjustments to the
1
installation height of the unit to eliminate the gap with the
ceiling. (Fig. 7-21)
Can be installed rotated 90°
CAUTION
If the screws are not sufficiently
tightened, trouble such as that
Fig. 7-17
shown in the figure below may
occur. Be sure to tighten the
screws securely.
Air leakage
Air leakage from
ceiling surface
Staining
Condensation, water leakage
Fig. 7-18
7-6. Wiring the Ceiling Panel
(1) Open the cover of the electrical component box.
(2) Connect the 7P wiring connector (red) from the ceiling
panel to the connector in the unit electrical component box.
(Fig. 7-22 )
Drainage check
(Direction that the unit faces has been changed to facilitate
explanation.)
Electrical component box cover
REF. mark
DRAIN mark
Screws
(3 locations)
Panel installation hole
(4 locations)
Fig. 7-19 * Pass the wiring connector through the clamp to fasten it in
place, as shown in the fi gure.
● If the connectors are not connected, the auto flap will not
operate. Be sure to connect them securely.
● Check that the wiring connector is not caught between the
electrical component box and the cover.
Do not allow
● Check that the wiring connector is not caught between the
gaps
unit and the ceiling panel.
7-7. How to Attach the Corner and Air Intake Grille
Ceiling panel
Fig. 7-20
Attaching the corner cover and air-intake grille
A. Attaching the corner cover
(1) Check that the safety cord from the corner cover is
fastened to the ceiling panel pin.(Fig. 7-23).
Pin
If a gap remains between
the ceiling surface and the
ceiling panel even after the
screws are tightened, adjust
the height of the unit again.
Place the corner cover so that the 3 tabs fit into the
holes in the ceiling panel. Then fasten it in place with the
Adjust so that there are no gaps.
supplied screws.
Fig. 7-21
(2) Use the supplied screws to attach the corner cover to the
ceiling panel.
B. Attaching the air-intake grille
● To install the air-intake grille, follow the steps for Removing
the grille in the reverse order. By rotating the air-intake
grille, it is possible to attach the grille onto the ceiling panel
from any of 4 directions. Coordinate the directions of the air-
intake grilles when installing multiple units, and change the
directions according to customer requests.
● When attaching the air-intake grille, be careful that the
flap lead wire does not become caught.
● Be sure to attach the safety cord to the ceiling panel
unit. This keeps the air intake grille from accidentally
dropping. (Fig. 7-24)
50
2011/01/12 13:56:03
Ceiling panel wiring connector
Fig. 7-22
Fig. 7-23