Options; Dial Options; Event Priority (Bgsm-120 Series Only); Codes (Bgsm-120 Series Only) - Bentel Security BGSM-120 Serie Manual De Usuario

White List




Options

This page is used to set the options relating to the Communicator board.

Dial options

This part is used to enter some of the characteristics relating to the telephone numbers used.
 Prefix: This Device will prefix the digits entered in this field to all the telephone numbers dialled through the GSM Interface
function. If necessary enter a Prefix (maximum 8 digits) in this field. If no Prefix is required, leave this field empty.
 Digits to Remove: If this Communicator is connected downstream to a switchboard, the telephone numbers (pro-
grammed on the Control panel) must be preceded by the switchboard number (normally one digit). As the switchboard
number is not required when calls are sent over the GSM Network, it must be removed from the digits which form the
telephone number. Enter the number of digits that form the switchboard number (e.g. if switchboard number is 01, enter
2 in the ―Digits to remove‖ field, as 2 numbers form the switchboard number).
 The telephone number should at least have two digits more that the number in the ―Digits to remove‖ area,
otherwise the engaged tone will be come through, e.g.:
– the dialled telephone number is 0123, with 2 digits to be removed = correct, the remaining number to be inserted is 23.
– the dialled telephone number is 123, with 2 digits to be removed = engaged tone, the remaining number to be inserted is 3.
 Enable Black List: Check this box if you do not wish to receive calls from telephone numbers, authorising only the
numbers selected previously using the White List function (Phonebook page->White List).
 Only the ―Black List‖ option cancels the call immediately.
 When the ―Black List‖ and ―Activates Output‖ options are enabled, there is a delay (some seconds) before
the call is cancelled;
When the Ring is selected for the ―Activates Output‖ option, there is a delay (some seconds) before the call is cancelled;
If the output cannot be activated, BGSM-120/BGSM-100 cancels the call immediately.

Event priority (BGSM-120 series only)

This page may be used to program several Communicator priorities, for the transmission of alarm events (see Priority management section).
 Off-Hook: This box can be used to establish the priority of telephone devices connected to the LI terminals (such as a
burglar alarm control panel). It is enabled  by default; to disable it remove the tick  .
 Voice Dialer: This box can be used to establish Voice dialer (voice message) priority. It is disabled  by default; to
enable it, mark it with a tick .

Codes (BGSM-120 series only)

 User Code: Enter the account code in this box (maximum 4 numeric characters) to activate outputs remotely. For further information, please
refer to the section ―Activating the Outputs->Remote Activation and Deactivation of the Outputs‖.The default code is set to ‗0001'.
 Installer Code: The Installer code can be entered in this field (maximum 4 numerical characters). This code allows
access to the ―Remote Programming‖ interface when required. The default code is set to ‗0002'.

Generic

This section may be used to set the audio levels of the loudspeaker and microphone fitted to the GSM Communicator.
 Speaker volume: The volume of the loudspeaker may be adjusted by shifting the cursor.
 Microphone volume: The volume of the microphone may be adjusted by shifting the cursor.
 CAUTION: if the volume on the microphone is too high, it may corrupt the DTMF tones from devices
connected to the LI terminals, making them unrecognizable.
 Tones...: Select the name of Communicator's country of installation; the selected country will establish a series of
parameters for the proper working of the simulated telephone call.
 LE failure timeout: Enter the time in seconds (between 10 and 3600 seconds) for the Line down on the LE terminals,
before the PSTN Fault event occurs.
 The time may increase up to 60 seconds if some telephone devices are connected to the terminals LI.
 LE restore timeout: Enter the time in seconds (from 30 to 3600) that the telephone line must be connected to the LE
terminals before the PSTN Fault event is reset.
BGSM-100/120
Black List

Accept incoming calls from any number

Refuse any incoming call
Accept incoming calls only from numbers having an enabled

White List option, refuse call coming from all other numbers
Functioning mode
G
19