Jacuzzi J-300 Serie Manual De Instalacion Y Uso & Mantenimiento página 29

I
Programming the Secondary Filtration Cycle
To make changes to the Secondary Filter Cycle, follow the steps below.
Press Press
PRESS PRESS
A. Press the Menu (
ary Filtration Cycle Menu. The LED screen will display "SF."
B. Press the Warmer (
changes. The LED will display the last cycle programmed and will
blink once to indicate the system is ready to accept changes.
C. Press the Warmer (
through the cycles, SF0 to SF3.
D. Once a cycle is selected, press the Jets 1 (
firm the selection. You must press the Jets 1 (
confirm your selection or the current settings will remain active.
E. The display will show the new cycle selected and it will blink
twice to indicate that the change has been accepted.
Note: If no button is pressed within 5 seconds of each selection the
screen will revert back to the Main Menu and the current settings will
remain active.
I
Economy Menu
In Economy mode, the heater only activates after a Secondary Fil-
tration cycle has finished. The heater will run for a maximum of
30 minutes. The heater can turn off prior to the 30 minutes if the
programmed water temperature is reached. The Secondary Fil-
tration program determines the number of cycles (from 1 to 4)
that the heater will be allowed to activate. For example, if you
have programmed the SF3 setting (10 minutes of filtration every
6 hours), then the heater will run, for a maximum of 30 minutes,
after the end of each of the 10-minute secondary filtration cycle,
for up to four times per day. Reference the chart that follows.
CYCLE RUN TIME
No filtration
10 minutes of filtration
every 12 hrs
10 minutes of filtration
every 8 hrs
10 minutes of filtration
every 6 hrs
Press
PRESS
Press
PRESS
OR
Will return Will return to
"SF" menu
to "SF" menu
) button twice to display the Second-
) button to prepare the system for
) or Cooler ( ) button to scroll
) button to con-
HEATER RUN TIME
Maximum of a half hour per day
Maximum of a half hour every 12 hrs
(after secondary cycle ends)
Maximum of a half hour every 8 hrs
(after secondary cycle ends)
Maximum of a half hour every 6 hrs
(after secondary cycle ends)
I
Programming the Economy Mode
To activate the Economy Mode, follow the steps below.
▲
OR
OR
A. Press the Menu (
conomy Menu. The LED screen will display "ECO."
B. Press the Warmer (
screen will display the current status of the Economy Mode set-
ting, either ON or OFF.
C. Press the Warmer (
D. Once the new setting appears of the display, press the Jets Jets
) button to 1 ( ) button to confirm your selection. The display of the LED
screen will blink twice to indicate that the change has been ac-
cepted. You must press the Jets 1 (
selection or the current settings will remain active.
Note: If no button is pressed within 5 seconds of each selection the
screen will revert back to the Main Menu and the current settings will
remain active.
I
Lock Menu
The Lock menu gives you the option to lock specific features of
the spa. There are three locking modes, L1, L2 and L3.
Note: When a lock mode is active, the LED display will flash be-
tween the lock mode and temperature.
L1 lock mode: The jets pumps and heater are deactivated. This
mode can be used when replacing or cleaning the spa filters.
Note: The spa should not be left in this lock mode for an extended
period of time. Especially in colder climate or when freezing con-
ditions exist.
L2 lock mode: The jets pumps, adjust temperature and CLEAR-
RAY buttons are deactivated. This mode can be used to prevent
unauthorized use of the spa.
L3 lock mode: The temperature and CLEARRAY buttons are de-
activated. This mode can be used to prevent unauthorized tem-
perature adjustments.
I
Programming the Lock Modes
◄
Press
PRESS
▲
29
◄ ◄
Press Press
PRESS PRESS
Press
PRESS
) button four times to display the E-
) button to enter the menu. The LED
) button to scroll through the settings.
◄ ◄ ◄
Press Press
PRESS PRESS
◄ ◄
▼
Press
PRESS
►
) button to confirm your
◄ ◄ ◄
Press Press
PRESS
PRESS
►
OR
Press
OR
OR