Vimar ELVOX 6600 Serie Instrucciones Instalador página 6

6600
DESCRIPTION
Types 6611, 661C, 6711 are a intercommunicating 6600 series open-voice
video interphone with 3,5" colour LCD screen for
systems. Type .../F versions have the same features and are programmed and
installed in the same way.
"Controls and Adjustments".
The videointerphones are supplied as standard with 6 push-buttons for auxiliary
functions or intercommuncating calls, 8 push-buttons for the following functions:
door lock release, self-start of video interphone in the system even when it has
not been called, conversation, stair light, internal voice line volume control, ring-
tone volume control, and two for the ringtone type. Two LEDs (red and green)
on the video interphone serve to indicate the following states: call signal mute,
unanswered calls, services not available and gate/door open.
- Flush-mounting of the video interphone (Art. 6611) requires the use of flush-
mounted back box type 6149.
- The installation of the surface wall-mounted monitor (type 6711) requires the
bracket for the wall-mounting supplied as standard.
Fig. 1
N
C
D
F
G
D L
Video interphone technical specifications
- Video interphone in ABS.
- Removable terminal block.
- Flat 3,5" LCD screen.
- Electronic circuit on interchangeable cards.
- PAL standard video signal.
- Operating temperature from 0° to +40° C.
- Electronic ringtone.
- Input for landing calls with different ringtone from entrance panel calls.
- Output for additional ringtone type 860A.
- Supply voltage provided by bus.
- Input for additional power supply (type 6923) if the system is configured to
enable simultaneous activation of more than two video interphones.
Controls and adjustments
A) Screen 3,5" LCD monitor.
B) Microphone.
C) Loudspeaker.
D) Pair of push-buttons.
1) When the video interphone is ON, the push-buttons can be used to adjust
the brightness.
2) When the video interphone is OFF, the push-buttons can be used to select
the tune for calls from a speech unit only. To program the tune: hold 1 of the 2
push-buttons down for at least 2 seconds, and press the push-buttons again
repeatedly to select the desired tune.
E) Pair of push-buttons
1) In conversation with the "I" push-button pressed, press the "E" push-but-
tons to increase or decrease the volume of the internal audio.
2) In rest position they adjust the chime volume: keep pressed for at least
2 seconds one of the two "E" push-buttons, press repeatedly the push-but-
tons to increase or decrease the chime volume. The "E" push-buttons adjust
the chime volume even during the immission of the internal or external call
sound. Once the sound emission has been ended, they adjust the contrast
while the screen is switched on.
F) Push-button : for activating 1st auxiliary service if connected by means
of 692RH (e.g. stair lights).
G) Push-button : to open the lock and terminate any conversation in
progress.
6
Due Fili Plus video door entry
A
B
E
H
I
E
M
H) Pushbutton : for self-start. It allows installation selfactivation from the
inside without call from the entrance panel.
I) Two-channel conversation push-button: after the call and/or
switch-on of the monitor press the pushbutton once to activate the audio.
Pressing it once again the conversation terminates.
The red LED remains lit for the whole conversation dwell.
L) Door open LED: the red led is lit when at least one door/gate is open,
it turns off when all doors are close (the function is optional according to the
type of installation).
M) 'Ringtone mute' LED: if the red LED lights up, this indicates that the call
is disabled (see point "E").
The red LED also remains lit for the entire duration of the conversation, i.e.
while the audio is active.
N) Push-buttons: for activation of auxiliary services or intercommunicating
calls (in function of the programming).
N.B. On the back of the video interphones type 6611 and 6711 is a RESET
push-button for use during programming. On video interphone 661C the RESET
push-button is on the bottom of the table-top conversion kit; all are equipped with
the A-B-C connectors for stabilising the video signal.
Connection and connector terminal board
+12, CH) Additional ringtone connection.
1, 2) BUS line.
E+, E- ) Additional supply voltage for video-interphone with power
supply type 6923.
FP, M) Connection for landing call push-button.
INSTALLATION 6611
- Install the video interphone away from sources of light and heat.
- Flush-mount back box type 6149 in the wall at a height of approximately 1.40
m from the ground to the lower border.
- Remove the plastic cross-piece from the back box (see part. 1, Fig. 2)
- Fix the video interphone to the back box with the 4 screws supplied (Fig. 4).
- Fit the side panels, taking care that the panel with the slot for the microphone
is fitted on the right (fig. 2).
Flush-mounted
version
Schermo non inclinabile
136
139
mm
59mm 10mm
141mm
(microphone)
part. 1
Fig. 2