Sammic SL-1100 Manual De Instrucciones página 8

The status of the inputs can be determined
according as the respective LEDs are on or
off.
Model Configuration:
Control of cycle time (Thermal Hang- up) as
a function of the boiler temperature:
·The electronic controller features the pos-
sibility of increasing the cycle time until the
preset temperature is reached in the boiler.
So, in the event the temperature of the boi-
ler were lower than the preset value, the
cycle would be extended until the preset
temperature is reached. This prevent rin-
sing with cold water. In order to enable this
feature, select the appropriate digit from
the following table:
T
HERMAL
C D B
ONFIG RAIN REAK
H - D
ANG UP
Nº P T
UMP ANK
OF CYCLE
SL1100
27 NO NO NO
SL1200
SL1100, SL1200
28 NO NO YES with thermal hang- up
of cycle
SL1100B
31 YES NO NO
SL1200B
SL1100B, SL1200B
32 YES NO YES with thermal hang- up
of cycle
SL1100BP
35 YES YES NO
SC1200BP
SL1100BP, SL1200BP
36 YES YES YES with thermal hang- up
of cycle
Configuration Selection:
The machine configuration number appe-
ars on the display for 2 seconds once the
main switch is turned on. In order to select
another configuration number, proceed as
follows:
1. Power the machine down.
2. Move the two microswitches (Fig B- 3) to
the ON position.
3. Power the machine up.
4. Press key (Fig B- 5): the configuration
number is displayed.
5. Press "Start" (Fig A- 5) to increment the
configuration number.
6. Press "Drain" (Fig A- 7) to decrement the
configuration number.
7. After selecting the number required,
press the Cycle Selection key (Fig A- 4) to
confirm.
8. Power the machine down.
9. Move the two microswitches (Fig B- 3) to
the OFF position.
10. Power the machine up: the selected
configuration number appears on the
display.
8 EN
OPERATION
S -
TART UP
1. Open the 3/4" stopcock to allow water to
enter the machine.
2. Turn on the switch. Turn on the booster
pump if one has been incorporated to
the machine.
3. Check that the filter of the motor- driven
pump (M), the upper filters (N) and the
drain plug are in place.
4. Turn the main switch (Fig. A- 1) to the
ON position for the automatic filling of
the wash tank and the connection of the
heater elements.
5. The light indicator (Fig.A, C) turns on
when
(55/60ºC) has been reached. If the was-
:
ISHWASHER MODEL
her has no automatic detergent dispen-
ser, introduce the detergent into the
tank: 1/2 coffee cup at the beginning of
the first cycle and a same amount every
10 cycles approximately.
6. Automatic Start Cycle:
- Place the objects to be washed in a
basket (rack).
- Press key A- 6 to activate the automa-
tic cycle. The associated LED turns on.
- Select the washing programme by
pressing key A- 4, according to the
level of soiling. The relevant red LED
will turn on.
- Close the door. The cycle will start auto-
matically and first the washing phase
indicator (A- g) will turn on, followed by
the rinsing indicator (A- h).
7. Non- automatic Start Cycle:
- Place the objects to be washed in a
basket (rack).
- Press key A- 6 with the LED off, to
command the manual start cycle.
- Close the door.
- Select the washing programme by
pressing key A- 4, according to the
level of soiling. The relevant red LED
will turn on.
- Press the Start Cycle key (A- 5). The
washing phase indicator light (A- g)
turns on. The machine completes the
entire washing cycle. If you press the
Start Cycle key (A- 5) again during the
washing
immediately shifts to the rinsing pro-
cess. Pressing the said key during the
rinsing phase causes the machine to
stop.
8. When the complete cycle has finished,
the two indicators (A- g) and (A- h) flash.
9. Models with a drain pump: With the door
open, press key (A- 7) to start the drain
pump for a given period of time, which
is long enough to empty the tub. At the
the washing temperature
phase, the programme
end of this time, the pump stops. Press
key (A- 7) to alternately start and stop
the pump. With overflow (C- 2) in place,
any residual water will be removed from
the tub.
10. Models "BP":
· The Break- tank has two (2) level swit-
ches (high- low) and an overflow pipe
discharging into the wash tank. Once
the main switch has been turned on,
filling of boiler, Break- tank and wash
tank is done automatically. Due to the
two level detection switches, the pres-
sure pump operates alternately.
· With a full tub,The drain pump works
at the same time as water enters the
Break- tank, so that water would flow
into the washing tank through the
break- tank overflow pipe in the event
of a level switch failure.
D
ETERGENT DISPENSER
The dishwasher is prepared for its fitting
with an adjustable detergent dispenser, the
part number of which appears on the spare
parts list. This dispenser has to be installed
in the machine base, in holes provided for
this purpose, as shown on the exploded
view. At the rear of the wash tank, there is
an opening where to insert the detergent
injection nozzle.
The dispenser delivers about 0.7ml/s of
detergent (maximum). At the first filling of
the tank, feeding of detergent is roughly
119ml in 170s, resulting in a maximum con-
centration of 3ml/l. At each cycle, the dis-
penser delivers 10ml of detergent. It is pos-
sible to reduce the injected quantity by tur-
ning the adjusting screw on the dispenser.
R
INSING AID DISPENSER
Verify that the rinsing aid reservoir is full.
With the machine running, actuate the
main switch several times (5 or 6) during
the washing cycle and check whether the
tube fills up with rinsing aid and goes in
the boiler. Setting the dispenser is done by
turning an adjusting screw on the front
lower panel in the direction shown on the
panel graph.
In order to determine whether the amount
of rinsing aid is adequate, look at the glas-
ses against the light. If there are water dro-
plets on the glass, the amount of rinsing
aid is insufficient; if streaks develop, the
quantity of rinsing aid is too much.
I
NSTALLATION OF AUXILIARY TABLES
The auxiliary tables are fastened with bolts
inserted into the threaded holes (D) either