Tabla de contenido
Idiomas disponibles
Idiomas disponibles
AC Input Current
Note!
The Input current of the drive depends on the operating state of the connected motor. The tables (chapter
3.4) shows the values corresponding to rated continuous service, keeping into account typical output power
factor for each size.
3.5 AC Output
Type
Inverter Output (IEC 146 class1),
Continuous service (@ 400Vac)
Inverter Output (IEC 146 class 2)
150% overload for 60s (@ 400Vac)
P
mot (recommended motor output):
N
@ U
=230Vac; f
=default; IEC 146 class 1
LN
SW
@ U
=230Vac; f
=default; IEC 146 class 2
LN
SW
@ U
=230Vac; f
=default; IEC 146 class 1
LN
SW
@ U
=230Vac; f
=default; IEC 146 class 2
LN
SW
@ U
=400Vac; f
=default; IEC 146 class 1
LN
SW
@ U
=400Vac; f
=default; IEC 146 class 2
LN
SW
@ U
=460Vac; f
=default; IEC 146 class 1
LN
SW
@ U
=460Vac; f
=default; IEC 146 class 2
LN
SW
U
Max output voltage
2
f
Max output frequency
2
I
Rated output current:
2N
@ U
=230-400Vac; f
= default; IEC 146 class 1
LN
SW
@ U
=230-400Vac; f
=default; IEC 146 class 2
LN
SW
@ U
=460Vac; f
=default; IEC 146 class 1
LN
SW
@ U
=460Vac; f
=default; IEC 146 class 2
LN
SW
f
switching frequency (Default)
SW
f
switching frequency (Higher)
SW
Derating factor:
Voltage Factor K
V
Temp. Factor K
for ambient temperature
T
Switching frequency K
*: Linear shapes for K
, K
V
T
The output of the drive is ground fault and phase to phase output short protected.
Nota!
The connection of an external voltage to the output terminals of the drive is not permissible! It is allowed to
disconnect the motor from the drive output, after the drive has been disabled.
The rated value of direct current output ( I
the switching frequency ( K
I
= I
x K
x K
x K
(Values of derating factor are the listed on table), with an overload capacity I
CONT
2N
V
T
sw
60 seconds.
AGy -L
2040 2055 2075 3110 3150 4185 4221 4301 4371 5450 5550 6750 7900 71100 71320 81600 82000
[kVA]
6.5
8.5
12
[kVA]
5.9
7.7
10.9
[kW]
2.2
3
4
[kW]
2.2
3
4
[Hp]
3
4
5
[Hp]
3
4
5
[kW]
4
5.5
7.5
[kW]
4
5.5
7.5
[Hp]
5
7.5
10
[Hp]
5
7.5
10
[V]
[Hz]
[A]
9.6
12.6
17.7
[A]
8.7
11.5
16.1
[A]
8.3
11
15.4
[A]
7.6
10
14.0
[kHz]
[kHz]
at 460 Vac *
0.87
F
, respectively in the ranges [400, 460] Vac, [40, 50]°C, (104, 122)°F.
) depends on the supply voltage ( K
CONT
) if higher than the default setting:
F
16.8
22.4
26.5
32
42
55
15.3
20.3
24.1
29
38.2
50
5.5
7.5
10
11
18.5
22
5.5
7.5
9
11
15
18.5
7.5
10
10
15
25
30
7.5
10
10
15
20
25
11
15
18.5
22
30
37
11
15
18.5
22
30
37
15
20
25
30
40
50
15
20
20
25
30
40
0.94 x U
(AC Input voltage)
LN
500
24.8
33
39
47
63
79
22.5
30
35
43
58
72
23.1
29.7
34
40
54
68
21.0
27.0
31
36
50
62
8
16
0.93
0.9
0.8 @ 50°C (122°F)
0.7 for higher f
64
79
98
128
145
173
58.3
72
89.2 116.5
132
157.5
22
30
37
55
55
75
22
30
37
45
55
55
30
40
50
75
75
100
30
40
50
60
75
75
45
55
75
90
110
132
45
55
55
90
90
110
60
75
100
125
150
150
50
60
75
100
125
150
200
93
114
142
185
210
250
85
104
129
168
191
227
81
99
124
161
183
218
74
90
112
146
166
198
4
8
0.87
sw
), the ambient temperature ( K
v
= 1.5 x I
MAX
224
277
204
252
90
100
90
100
125
125
100
125
160
200
160
200
200
250
200
250
324
400
295
364
282
348
257
317
4
-
Output-g
) and
T
for
CONT
53
Capítulos
Tabla de contenido
