Input - gefran AGy -L Manual De Instrucciones

3.4 Input

Type
U AC Input voltage
LN
AC Input frequency
I AC Input current for
N
continuous service :
- Connection with 3-phase reactor
@ 230Vac; IEC 146 class 1
@ 400Vac; IEC 146 class 1
@ 460Vac; IEC 146 class 1
- Connection without 3-phase reactor
@ 230Vac; IEC 146 class 1
@ 400Vac; IEC 146 class 1
@ 460Vac; IEC 146 class 1
Max short circuit power without line
reactor (Zmin=1%)
Overvoltage threshold (Overvoltage)
Undervoltage threshold (Undervoltage)
Braking IGBT Unit Standard internal
(with external resistor);
MAX Braking torque:
*: For the specified power sizes, the external reactor is strongly recommended
Power Supply and Grounding
1) Drives are designed to be powered from standard three phase lines that are electrically symmetrical with respect to
ground (TN or TT network).
2) In case of supply with IT network, the use of delta/wye transformer is mandatory, with a secondary three phase
wiring referred to ground.
In case of a three phase supply not symmetrical to ground, an insulation loss of one of the devices con-
nected to the same network can cause functional problem to the drive, if the use of a delta/wye transformer
is avoided.
Caution
Please refer to the following connection sample.
Safety
ground
Mains connection and inverter output
The drivea must be connected to an AC mains supply capable of delivering a symmetrical short circuit current lower or
equal to the values indicated on table. For the use of an AC input choke see chapter 4.
Note from the table the allowable mains voltages. The cycle direction of the phases is free.
Voltages lower than the min. tolerance values can cause the block of the inverter.
Adjustable Frequency Drives and AC Input filters have ground discharge currents greater than 3.5 mA. EN 50178 specifies
that with discharge currents greater than 3.5 mA the protective conductor ground connection (PE1) must be fixed type.
52
2040 2055 2075 3110 3150 4185 4220 4300 4370 5450 5550 6750 7900 71100 71320 81600 82000
[V]
[Hz]
[A] 7 9.5 14 * 18.2 25 *
[A] 7.9 10.7 15.8 * 20.4 28.2 * 36.7
[A] 7 9.3 13.8 * 17.8 24.5 * 32.5
[A] 11 15.5 21.5 * 27.9 35.4 *
[A] 12 16.9 24.2 * 30.3 40 *
[A] 10.4 14.7 21 * 26.4 34.8 *
[kVA] 650 850 1200 1700 2250 2700 3200 4200 5500 6400 7900 9800 12800 14500 17300 22400 27700
[V]
[V]
150% 70% 90%
L1
L2
L3
Earth
230 V -15% ... 480 V +10%, 3Ph
50/60 Hz ±5%
32.5 39 55 69 84
44 62 77 94
37 53 66 82
For these types an external inductance is recommended
440VDC (for 230VAC mains), 820VDC (for 400VAC mains),
820VDC (for 460VAC mains)
230VDC (for 230VAC mains), 380VDC (for 400VAC mains),
415VDC (for 460VAC mains)
All wires (including motor ground) must
be connected inside the motor terminal box
98 122 158 192 220
110 137 177 216 247
96 120 153 188 214
150%
275 n.a.
309 365
268 318
input-g
AGy -L