Choosing The Place Where The Safety Seat Is To Be Installed; Installing Your Iquartz In The Vehicle; Installing Your Iquartz With The Fixed Anchors; Reclining The Seat - JANE iquart2 Manual De Instrucciones

!
WARNING: This position should be adjusted as the child grows.

Choosing the place where the safety seat is to be installed

Choosing the correct place to install the safety seat in the car can reduce the risk of the child
suffering injuries in the event of an accident. The safety seat should preferably be installed
on rear seats. There are two possible installation options:
ISOfix
With ISOfix anchors and with the 3-point seat belt.
! WARNING: Raise or remove the headrest of the vehicle seat if it interferes with the
headrest of the safety seat, so the backrest is firmly secured against the vehicle seat.
On seats fitted with a frontal air-bag, move the seat as far back as possible.
F. INSTALLING YOUR iQUARTZ IN THE CAR
Follow the steps below carefully:

Installing your iQUARTZ with the fixed anchors:

2a
Extract the anchor by pressing the red levers on the sides (10).
Make sure that both anchors are open, the red signal on the anchor button should be
2b
displayed (9).
Position your iQUARTZ on the vehicle seat following the advice and warnings detailed in the
GENERAL INSTRUCTIONS. Before installing the safety seat, check your vehicle seat to find the
two ISOfix anchors. When you have located them, position your iQUARTZ so that the fixed
anchors (8) are lined up with the ISOfix anchors of your vehicle.
22
EN
IM-2004,01 iQUARTZ text esp modificado.indd 22
Just with the 3-point seat belt.
2c
Press the fixed anchors towards the vehicle seat until they lock into place, check that the
green signal is displayed on the two ISOfix release buttons (10).
Continue pressing firmly until the booster seat is pushed against the backrest of the vehicle
2d
seat. Make sure that it is securely in place by pulling the booster seat.
Place the child in the iQUARTZ and make sure that he is sitting firmly against the backrest,
2e
put the seat belt on and fasten it.
2f
Insert the shoulder belt through the red belt guide on the headrest (6).
Pass the lap belt under both armrests of the booster seat, the zone where the belt should
2g
go over is again indicated in red (7). Pass the shoulder belt over the armrests of the booster
seat. Make sure the belt is flat and not twisted anywhere. Lastly, tighten the belt.
To get the child out of the safety seat, simply unfasten the seat belt. When you want to take
the iQUARTZ out of the car, pull the ISOfix anchor buttons (10) while removing the booster seat.
Installing your iQUARTZ just with the 3-point seat belt
Position your iQUARTZ on the vehicle seat following the advice and warnings detailed in the
GENERAL INSTRUCTIONS.
2e Place the child in the iQUARTZ and make sure that he is sitting firmly against the backrest,
put the seat belt on and fasten it.
2f
Insert the shoulder belt through the red belt guide on the headrest (6).
Pass the lap belt under both armrests of the booster seat, the zone where the belt should
2g
go over is again indicated in red (7). Pass the shoulder belt over the armrests of the booster
seat. Make sure the belt is flat and not twisted anywhere. Lastly, tighten the belt.

Reclining the seat:

The seat can be reclined to make it more comfortable for the child. Maximum protection is
achieved when the seat is not reclined.
To recline the seat, pull the reclining lever (12) on the front of the booster seat and slide it
3a
to the required position. There are 3 different positions.
WARNING: Do not adjust the reclining position while the child is in the seat. When you
!
change the reclining position of your iQUARTZ you need to adjust the tension and length
of the seat belt. Only alter the iQUARTZ when the car is stationary.
19/1/18 13:20