Functional Description - Makita DUC305 Manual De Instrucciones

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge. F ailure to h ol d t h e tool an d t h e batter y
cartridge firmly may cause them to slip off your hands
an d result in d amage to t h e tool an d batter y c artri d ge
and a personal injury.
Fig.3: 1. R e d in d i c ator 2. Button 3. Batter y c artri d ge
T o remo v e t h e batter y c artri d ge, sli d e it f rom t h e tool
w h ile sli d ing t h e button on t h e f ront o f t h e c artri d ge.
T o install t h e batter y c artri d ge, align t h e tongue on t h e
batter y c artri d ge w it h t h e groo v e in t h e h ousing an d slip
it into pla c e. I nsert it all t h e w a y until it lo c ks in pla c e
w it h a little c li c k. I f y ou c an see t h e re d in d i c ator on t h e
upper si d e o f t h e button, it is not lo c ke d c ompletel y .
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. I f not,
it may accidentally fall out of the tool, causing injury to
y ou or someone aroun d y ou.
CAUTION:
Do not install the battery cartridge
forcibly. I f t h e c artri d ge d oes not sli d e in easil y , it is
not being inserte d c orre c tl y .
NOTE: T h e tool d oes not w ork w it h onl y one batter y
c artri d ge.
NOTE: Pay attention to the position of your fin-
gers w h en installing t h e batter y . T h e button w ill be
d epresse d unintentionall y .
Tool / battery protection system
T h e tool is e q uippe d w it h a tool / batter y prote c tion s y s-
tem. T h is s y stem automati c all y c uts o f f po w er to t h e
motor to e x ten d tool an d batter y li f e. T h e tool w ill auto-
mati c all y stop d uring operation i f t h e tool or batter y is
pla c e d un d er one o f t h e f ollo w ing c on d itions.
Overload protection
W h en t h e tool is operate d in a manner t h at c auses it
to d ra w an abnormall y h ig h c urrent, t h e tool automat-
i c all y stops an d t h e main po w er lamp w ill blink. I n t h is
situation, turn t h e tool o f f an d stop t h e appli c ation t h at
c ause d t h e tool to be c ome o v erloa d e d . T h en turn t h e
tool on to restart.
Overheat protection
W h en t h e tool is o v er h eate d , t h e tool automati c all y
stops an d t h e c apa c it y in d i c ator lamp w ill blink as illus-
trate d . I n t h is situation, let t h e tool c ool d o w n be f ore
turning t h e tool on again.
Capacity indicator status
On
Overdischarge protection
W h en t h e batter y c apa c it y be c omes lo w , t h e tool stops
automati c all y . I f t h e pro d u c t d oes not operate e v en
w h en t h e s w it c h es are operate d , remo v e t h e batteries f rom t h e tool an d c h arge t h e batteries.
Indicating the remaining battery capacity
Fig.4: 1. C h e c k button 2. C apa c it y in d i c ator
T h e remaining batter y c apa c it y is s h o w n w h ile y ou
are pressing t h e c h e c k button. T h e c apa c it y in d i c ators
c orrespon d to ea c h batter y .
Capacity indicator status
On
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
Fig.5: 1. I n d i c ator lamps 2. C h e c k button
P ress t h e c h e c k button on t h e batter y c artri d ge to in d i-
c ate t h e remaining batter y c apa c it y . T h e in d i c ator lamps
lig h t up f or a f e w se c on d s.
Indicator lamps
Lighted
12 ENGLISH
Off
Blinking
Off
Blinking
Off Blinking
Status
O v erh eated .
Remaining
battery
capacity
5 0% to 1 00%
20% to 5 0%
0% to 20%
C h arge th e
battery
Remaining
capacity
75 % to 1 00%
5 0% to 75 %
25 % to 5 0%
0% to 25 %
C h arge th e
battery .