INSTRUCTIONS FOR USE
OPERATIONS THAT CAN ONLY BE CARRIED OUT BY REMOTE CONTROL
Clock regulation
Press and hold the key "M" for 2 seconds to access the "CLOCK" menu. This allows you to set the internal electronic board
clock.
By then pressing the key "M", the following data appears in sequence and can be regulated:
day, month, year, hour, minutes, day of the week.
The wording "SAVE??" will appear for confirmation with "M". This will allow you to check that the operations performed are
correct, prior to completion (the wording "SAVE" will then be shown on the display).
Weekly timer
Press and hold the "M" key on the remote control for 2 seconds. This turns on the clock regulation and by pressing the '+'
key, the weekly timer function is accessed, with the display showing the description "PROGRAMM ON/OFF".
This function allows you to set a number of times the insert turns on and off per day (up to a maximum of three), each
day of the week.
As you confirm the display with the key "M", one of the following options will appear:
NO PROG. (no programme set)
DAILY PROGRAM (single programme for every day of the week)
WEEKLY PROGRAM. (specific programme for each day individually)
Use the "+" and "–" keys to switch between programmes.
Use key "M" to confirm the option "DAILY PROGRAM" to choose the number of programmes (turn on/off) to be car-
ried out per day.
Use the "DAILY PROGRAM" to set identical programme/s for every day of the week.
By then pressing the "+" key, the following can be seen:
- Prog. no.
- 1st prog. (one turn on and one turn off per day), 2nd prog. (identical), 3rd prog. (identical)
Use the "–" key to show in reverse order.
If the 1st programme is selected, the turn on time is shown.
The display shows: 1 "ON" at 10 Use the "+" and "–" key to change the hour. Confirm with the "M" key.
The display shows: 1 "ON" at 30 Use the "+" and "–" key to change the minutes. Confirm with the "M" key.
The same applies for the turn-off time to be set and for subsequent turning on and off.
Confirm by pressing "M" and the wording "SAVE??" will appear on the display.y.
When confirming "WEEKLY PROGRAM", you will need to choose the day to which the programming is to apply:
1 Mon ; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sa; 7 Sat
Once you have chosen the day, use the "+" and "–" key and confirm with the "M" key, to programme in the same way
as for the "DAILY PROGRAM", choosing whether or not to enable a programme for each day of the week, and if so
choosing number of interventions and at what times.
Should you make an error during programming, you can leave the programme without saving. As you press a key,
the display will show the word "NO SAVE".
Changing pellet loading
Press the "M" button for two seconds from the radio control and scroll the display instructions with the "+" and "-" but-
tons. You will come across the message "User menu" and when you confirm, the message "ADJ-PELLET and ADJ-
DRAUGHT" will appear.
If we set "Auto-adjust. ON", the system will automatically adjust pellet dropping. Alternatively, if we set "Auto-adjust.
OFF," we can manually correct pellet dropping, varying the range in terms of percentages (+/- 30 %).
By confirming this function with the menu key, you can access the function to adjust pellet loading. By decreasing the
value set, pellet loading is decreased. By increasing the value set, pellet loading increases. This function is useful if
changing the pellet type for which the insert has been calibrated and loading therefore needs correcting.
Should this correction not suffice, contact the Edilkamin-authorised Dealer, to establish the new operating axis.
Notes on flame variability
Flame status may vary depending on the type of pellet used, in addition to normal solid fuel flame variability and
regular combustion chamber cleaning carried out automatically by the boiler.
(N.B.: which does NOT replace necessary cold suction by the user prior to ignition).
30