Husqvarna W520i Manual Del Usuario página 24

To install the sensor
1. Make sure that the sensor is connected to the
Husqvarna Fleet Services
pairing operation between the app and the product
on page 23 .
2. Drill 2 holes by the marks in the enclosure slot. (Fig.
38)
Note:
Make sure that the holes are the same
dimension as the rivets supplied with the sensor.
3. Use a pair of pliers to remove the outer holes on the
sensor slot. (Fig. 39)
4. Drill 2 holes by the marks in the sensor slot. (Fig. 40)
5. Align the sensor slot with the enclosure slot. (Fig. 41)
6. Attach the sensor slot with the rivets.
7. Install the sensor in the sensor slot. Align the white
mark on the sensor with the mark on the sensor slot.
(Fig. 42)
8. Close the lid to the sensor and lock it with the sensor
key. Make sure that the top of the Husqvarna "H"
points away from the safety key. (Fig. 43)
To set the product in operation position
1. Lift the handle to upright position. (Fig. 44)
2. Move the knobs up in the direction of the handle until
they stop and you hear a click. (Fig. 31)
3. Tighten the knobs fully.
To set the cutting height
The cutting height can be adjusted in 6 levels.
1. Push the cutting height control in the direction of the
wheel and then rearward to increase the cutting
height.
2. Push the cutting height control in the direction of the
wheel and then forward to decrease the cutting
height. (Fig. 45)
CAUTION:
too low. The blades can hit the ground if the surface of the lawn is not level.
Battery
WARNING:
you must read and understand the safety
chapter. You must also read and understand
the operator's manual for the battery and the
battery charger.
Battery status
The display shows the remaining battery capacity and if
there are problems with the battery. The battery capacity
is shown for 5 seconds after the product is switched off
24
™ To do a
app. Refer to
Do not set the cutting height
Before you use the battery,
or the battery indicator button is pressed. The warning
symbol on the battery is on when an error has occurred.
Battery on page 27 .
See
(Fig. 46)
LED lights
All LEDs are lit
LED 1, LED 2, LED 3 are
lit
LED 1, LED 2 are lit
LED 1 is lit
LED 1 flashes
To charge the battery
Charge the battery before the first use. The battery is
only 30% charged when supplied to the customer.
Note:
The battery charger must be connected to the
voltage and frequency specified on the rating plate.
The battery does not charge if the battery temperature is
above 50°C. The battery charger decreases the
temperature of the battery before it starts to charge.
1. Connect one end of the power cord for the battery
charger into the socket of the battery charger.
2. Connect the other end of the power cord for the
battery charger in an grounded mains socket. The
LED on the battery charger flashes green one time.
(Fig. 47)
3. Put the battery in the battery charger. The green light
on the charger comes on when the battery is
correctly connected to the battery charger. (Fig. 48)
4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
Battery charging status
A Husqvarna Li-ion battery can be charged or used at all
charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display
LED 1 flashes
LED 1 is lit, LED 2 flashes 25%-50%
Battery status
Fully charged (75-100%)
The battery is 50%-75%
charged
The battery is 25%-50%
charged
The battery is 0%-25%
charged.
The battery is empty.
Charge the battery.
Charging status
0%-25%
1484 - 005 - 23.09.2020