Programming - Beninca CP.BN Manual De Instrucciones

Wire connections shown in Fig. 1 are described hereunder:
Terminal
Function
no.
1-2 24Vac/dc
3-4
Antenna
9-10 SCA/SRL/2° Ch
Radio
11-12 24 Vdc
13-14 Flashing light
17 PED/CLOSE
18 Step-by-Step/OPEN With "OPEN/CLOSE" logics Off: Input, step-by-step push-button (Normally Open contact).
19 PHOT C
20 PHOT
21 STOP
22 COM
23-25 Motor 1
24 Motor 1, Ground
26-28 Motor 2
27 Motor 2, Ground
BN.CB Buffer battery
1) Cut off power supply.
2) Manually release the gate leaves, move them to around half their stroke and block them again.
3) Restore power supply.
4) Send a sep-by-step control by using the push-button connected to the Input, Step-by-Step (PP), radio control or push-button <->.
5) The gate leaves should open.
In the negative, the operation wires of the motor should be inverted by turning motor 1 connector by 180° and inverting wires
26<>28 for motor M2.
6) Select the motor which should start the operation first in the opening phase by using the MINV logics, see Fig.4.
7) Carry out an autoset procedure (see SET menu).
The programming of the various functions of the control unit is carried out using the LCD display on the control unit and setting the
desired values in the programming menus described below.
The parameters menu allows you to assign a numerical value to a function, in the same way as a regulating trimmer.
The logic menu allows you to activate or deactivate a function, in the same way as setting a dip-switch.
Other special functions follow the parameters and logic menus and may vary depending on the type of control unit or the software
release.
USE OF PROGRAMMING KEYS
Press <PG> key to gain access to the Main Menu (PAR>>LOG>>RADIO>>...). These keys can be selected by pressing + and
– keys.
Select the Main menu with <PG> key to enter the desired Function Menu .
• If <+> is pressed, the Function Menu can be scrolled from top to bottom.
• If <-> is pressed, the Function Menu can be scrolled from bottom to top.
12
CP.BEN CONTROL UNIT
WIRE DIAGRAM
Description
Input, power supply, 24Vac/24Vdc.
Connection to insertable radio-receiver card antenna (3-screen/4-signal).
Volt-free contact, Normally Open, controlled by logics "2° Ch Radio" (2
and "SRL".
With "2 Radio channel" logics On: active output as 2
nd
With "2 Radio channel" logics Off:
nd
- With "SRL" logics On: Contact for courtesy light control
- With "SRL" logics Off: Contact for "SCA" open gate light
Output, accessories power supply, 24Vc/0.5A max (12+/11-).
Connection of warning flashing light, 24Vdc 15W max.
With "OPEN/CLOSE" logics Off: Input, pedestrian push-button (Normally Open contact). It
controls motor 1 opening.
With "OPEN/CLOSE" logics On: Input, close push-button (Normally Open contact). It
controls both motors.
With "OPEN/CLOSE" logics On: Input, OPEN push-button (Normally Open contact). It
controls the opening of both motors.
Input, photocell is activated only during closure (Normally Closed contact Normally Closed
contact)
Input, photocell is activated during opening and closing (Normally Closed contact)
Input, STOP push-button (Normally Closed contact)
Common for all control inputs.
Pre-wired rapid connector, motor 1
Ground of motor 1
Extractable connector for connection of motor 2: 24Vdc 120W max
Ground of motor 2
Rapid connector for connection of battery charger card BN.CB
TO CHECK CONNECTIONS

PROGRAMMING

Radio channel)
nd
Radio channel.
nd