Monacor TXA-1022CD Manual De Instrucciones página 3

CD/MP3 Player with Remote Control
The player allows to replay standard audio CDs and
CDs, USB mass storage devices and SD cards with
MP3 files.
Note: With rewritable CDs (CD-RW), problems may occur
when replaying according to the CD type, the CD burner
and the burning programme used.
The anti-shock memory of the player will be able to
compensate temporary shocks or vibrations occur-
ring during the CD sampling; however, it will not be
able to compensate continuous, severe vibrations.
For CD operation, the system must therefore always
be operated in a stationary way, i. e. it must be
placed on a solid, immobile ground.
Note concerning sound interruptions and reading
errors
Cigarette smoke and dust will easily penetrate through
all openings of the unit and also settle on the optics of the
laser sampling system. If this deposit causes reading
errors and sound interruptions, the unit must be cleaned
by skilled personnel. Please note that there will be a
charge on cleaning, even during the warranty period!
The IR remote control for the player is supplied with
a battery. Prior to initial operation, remove the foil
from the battery holder. When pressing a button,
always direct the remote control to the infrared sen-
sor (4) of the player. There must be no obstacles
between the sensor and the remote control.
If the remote control is not used for a longer time,
remove the battery as a precaution so that the
remote control will not be damaged in case the bat-
tery should leak.
Replacing the battery: Push the latch of the battery
holder to the right (first arrow in the figure below) and
remove the holder (second arrow). Remove the old
battery and insert the new battery (3 V button cell,
type CR 2025) into the holder with the positive pole
pointing upwards. Push the holder back into the
remote control.
Batteries must not be placed in the house-
hold waste. Always take them to a special
waste disposal, e. g. collection container
at your retailer.
1 Switching on and off /
inserting and removing the playing medium
The player is switched on and off with the POWER
button (3).
Inserting a playing medium:
– Insert a CD with the lettering showing upwards
into the CD slot (1) until it is retracted automati-
cally
and / or
– connect a USB storage device (e. g. USB flash
drive, USB hard disk with separate power supply)
to the USB port (2)
and / or
– insert an SD card (bevelled corner upward and
contacts to the right) into the slot (5) until it will
engage.
Removing a playing medium:
To eject the CD, press the eject button STOP/ EJ or
EJECT (11) twice (first time: switching to stop,
second time: CD is ejected). After ejecting, the CD
can be retracted again by pressing the eject button.
Disconnect the USB storage device from the USB
port and to remove the SD card, first unlock it by
pushing it into the slot, then remove it. USB storage
device and SD card should not be removed during
their replay.
2 Selecting the playing medium
Each time the speaker system is set into operation,
the CD player mechanism is automatically selected.
It is possible to select the playing media with the
button CD / USB / SD (6): After pressing the button,
the selected medium is shown on the display ( ,
or ). Shortly after that its replay will start.
If a USB storage device or an SD card has been
selected and is then removed, the player automati-
cally switches over to the CD player mechanism.
The same happens when a new CD is retracted.
3 Replay / pause / stop
After reading in the playing medium, the replay starts
(insertion ). To interrupt the replay (insertion ) and
to continue it again, press the button PLAY/ PAUSE
or (10). The display shows the time already
played of the track (min.: sec.).
To stop the replay, the following buttons may be
pressed:
– Button (18)
– Button STOP/ EJ or EJECT (11)
In the stop mode the display is switched to the time
indication "00 : 00". To restart the replay with the first
track, press the button PLAY/ PAUSE or
4 Adjusting the volume / muting
Adjust the volume with the control VOLUME (13).
To deactivate and reactivate the sound, press the
button (21).
5 Track selection
Audio CDs
For audio CDs (insertion "CD") the display shows the
track number during replay and pause and the total
number of all tracks in the stop mode.
1. Next or previous track:
Use the buttons REV/ F.WD or S
[REV/ S
= return to the track beginning first,
each time the button is pressed the player goes
back another track, F.WD/
ward].
2. Entering track number:
Enter the track number via the numerical keys
(14) and confirm with the button ENTER (20).
MP3 playing media
For playing media with MP3 files (insertion "MP3")
the display shows the folder number and the track
number within the folder during replay and pause.
Tracks without folder in the main directory are
assigned to folder No. 1. In the stop mode the total
number of the folders and the total number of the
tracks of the playing medium are shown.
1. Next or previous track:
Each time the button FOLDER (7) is pressed, the
player goes to the next folder. For track selection
use the buttons REV/ F.WD or S
[REV/ S = return to the track beginning first, each
time the button is pressed, the player goes back
S = one track forward].
another track F.WD/
2. Entering the track number:
Via the numerical keys (14) enter the number of
the track on the playing medium (not the number
within the folder!) and confirm with the button
ENTER (20).
Note: In some cases the player will not go to the track
beginning first when the return button is pressed, it will
immediately go to the previous track (e. g. in case of CD
operation in the pause mode).
6 Fast forward and reverse
For fast forward and reverse use the buttons
FB/ F.F or / (8): FB or
= forward. Press the respective button shortly.
If the desired spot is reached, press the button
PLAY/ PAUSE or (10) for replay.
7 Changing the replay speed and pitch
The PITCH buttons (12) allow to change the replay
speed and thus the pitch.
button HI or HIGH:
to increase the replay speed in 10 steps
button LO or LOW:
to decrease the replay speed in 10 steps
Press the corresponding button repeatedly until the
desired speed is reached. Each time the button is
pressed, the display shortly shows the selected
adjustment, e. g.
To return to standard speed, press the button NOR
once.
8 Repeat functions / random track sequence
Three repeat functions are available for selection.
The selected function is shown on the display. Use
the button REP (17) to select:
.
– "REPEAT 1": continuous repeat of the track
– "REPEAT FOLDER" (for MP3 mode only):
continuous repeat of all tracks in the folder
– "REPEAT ALL": continuous repeat of all tracks on
the playing medium
– No REPEAT insertion: no repeat function acti-
vated; after playing all tracks, the player is set to
stop
To replay the tracks in a random order, press the
button RAN (16). "SHUFFLE" is inserted on the
display. To switch off the shuffle function, press the
button again.
An activated repeat function will be deactivated
S (9)
/
when the shuffle function is activated and vice versa.
9 Playing a loop
S = one track for-
A section within a track can be continuously
repeated as a loop.
1) If the starting point of the section is reached in the
track currently
A – B (19). The display shows "A ©".
2) If the end point of the section to be repeated is
reached, press the button again. The display
shows "A © B". The section is repeated perma-
nently.
3) To end the loop, press the button a third time.
"A © B" will be extinguished.
10 Programming a track sequence
1) To switch to the programming mode, press the
button PROG (15). "PROGRAM" is in serted on
S (9)
/ the display.
2) Select the first track of the track sequence:
either
– go to the track with the buttons REV/ F.WD or
S
/
folder with the button FOLDER (7), if required
or
– enter the track number directly via the numeri-
cal keys (14) [for MP3 operation: the number of
the track on the playing medium, not in the
folder!]
and press the button ENTER (20) to confirm. The
display shows the memory location number
instead of the time indication.
For all further tracks proceed the same way until
the complete track sequence (10 tracks max.)
= reverse, F.F or
has been programmed.
3) To start the track sequence, press the button
PLAY/ PAUSE or
extinguished and "MEMORY" will be in serted. To
return to replay in standard order, press the
button PROG: "MEMORY" will be extinguished
and the programming will be deleted.
4) If no repeat function is activated ("REPEAT 1" and
"REPEAT ALL" are available), the player is set to
stop after playing the track sequence, thus the
track sequence is deleted.
when the standard speed has
been increased by 5 steps
when the standard speed has
been decreased by 2 steps
playing, press the button
S (9); for MP3 operation first select the
(10), "PROGRAM" will be
3